Asus V2-P5G31 driver and firmware
Related Asus V2-P5G31 Manual Pages
Download the free PDF manual for Asus V2-P5G31 and other Asus manuals at ManualOwl.com
Installation Manual - Page 1
English
V-Series
ASUS PC (Desktop Barebone)
Installation manual
Installation Manual - Page 2
... Guide.
1. PS/2 keyboard port ( )
2. PS/2 mouse port ( )
3. VGA port ( )
4. Parallel port (
)
5. USB 2.0 ports ( ) (some models may have four rear USB 2.0 ports)
6. LAN (RJ-45) port ( )
7. One of the following ports:
• E-SATA port (
)
• Serial (COM1) port ( )
• DVI port (
)
• Optical S/PDIF Out port ( )
• Coaxial S/PDIF Out port ( )
8. IEEE 1394a port...
Installation Manual - Page 3
...channel
Refer to the configuration table in the User Guide for details.
Internal components
5
6 7
8
2
3
4
1
1. Front panel cover 2. 5.25-inch optical drive bays 3. Floppy disk drive bay 4. Hard disk drive bay
5. Power supply unit 6. Chassis fan slot 7. ASUS motherboard* 8. Expansion slot metal brackets
NOTE: *Refer to the system User Guide for motherboard details.
Installation manual
Installation Manual - Page 4
... in your area is 100‑127 V, set the switch to 115 V.
If the voltage supply in your area is 200‑240 V, set the switch to 230 V.
NOTE: Refer to the system User Guide for the exact location of the voltage selector...on the
right side of the assembly are exposed. 5. Remove the front panel assembly, then set aside.
3
4
Air duct
1
23
4
1 4
3 2
Chassis tab holes 3
Installation manual
Installation Manual - Page 5
...CPU socket on the motherboard.
2. Press the load lever with your thumb (A), then move it to the left (B) until it is released from the retention tab.
Retention tab A
CAUTION. To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU.
B Load lever
3. Lift the load... the load plate window to remove
(4B).
3
PnP cap Load plate
4A
5. Position the CPU over ...
Installation Manual - Page 6
... on top of the installed CPU, making sure that the four fasteners match the holes on the motherboard.
2. Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place.
3. When the fan and heatsink assembly is in place, connect the CPU fan cable to the connector on the motherboard.
A B
B A
1 1
Installation manual
Installation Manual - Page 7
... the fan and heatsink to the module retention module base.
5. Connect the CPU fan cable to the connector on the motherboard.
CAUTION. Do not forget to connect the CPU fan connector! Hardware monitoring error can occur if you fail to plug this connector.
CPU fan
Retention bracket lock
Retention bracket
1 2
4 3
5
CPU fan connector CPU heatsink Retention module base
Installation manual
Installation Manual - Page 8
... clips snap inward.
CAUTION: • Unplug the power supply before adding or removing DIMMs. Failure to do so may cause damage to the motherboard and/or components. • A DDR DIMM is... keyed with a notch so that it fits in only one direction. Do not force a DIMM into a socket to avoid damaging the DIMM.
Installing an expansion card...
Installation Manual - Page 9
Installing storage drives
Optical drive
1. Place the chassis upright, then remove the upper 5.25" drive bay metal plate cover.
2. Insert the optical drive to the bay,
3
then carefully push the drive until its
screw holes align with the holes on
the bay.
3. Secure the optical drive with two screws on both sides of the bay.
4. Connect the IDE (A) and power (B) plugs to connectors...
Installation Manual - Page 10
... SATA HDD: Connect the SATA
SATA
IDE
signal and power plugs to the
connectors at the back of the drive.
For IDE HDD: Connect the IDE and power plugs to the connectors at the back of the drive.
Removing the bay covers and reinstalling the
front panel assembly and side cover
If you installed an optical and/or floppy disk drive...