Belkin F5D6001_ver2 driver and firmware
Related Belkin F5D6001_ver2 Manual Pages
Download the free PDF manual for Belkin F5D6001_ver2 and other Belkin manuals at ManualOwl.com
User Guide - Page 3
... of Package 3 Knowing Your Belkin Wireless Desktop Network Card 4 Optional Desktop Antenna 5 Installing and Setting Up the Card 6
Step 1-Software and Driver Installation 6-7 Step 2-Installing the Card into Your PC
for Windows 98, Me, 2000, and XP 7-8 Step 3-Finishing the Installation 9 Uninstalling the Software and Drivers 9 Using the Card 10-13 Windows XP 10 Windows 98, Me, 2000 13...
User Guide - Page 4
...or lower Outdoor: 490' (150m) @11Mbps, 980' (300m) @ 5.5Mbps or lower
System Requirements
• PC with available PCI expansion slot • PC running Windows 95, 98 SE, 2000, NT®, Me, or XP • CD-ROM drive (for loading software)
Contents of Package
• Belkin Wireless Desktop Network Card • External Antenna • Software CD • Quick Installation Guide • User...
User Guide - Page 6
... you install the software, it will not work until you install the software. 2. Install the Card inside of your PC. 3. Turn on your PC and let Windows operating system (OS) finish installing the Card. NOTE: INSTALL THE SOFTWARE FIRST BEFORE YOU INSTALL THE CARD INTO YOUR PC
Step 1: Software and Driver Installation
1. Insert the CD into your CD-ROM drive. 2. The "Wireless Desktop Network Card Setup...
User Guide - Page 7
... the cover to your
computer, reconnect all of the cables, and turn it back on. Proceed to Step 3.
8
wireless networking
Step 3: Finishing the Installation
1. Turn your computer on.
2. Depending on your operating system, Windows OS may detect the Card and launch the "Found New Hardware" wizard. Click "Next".
3. Your Windows OS may ask you where the drivers are located. Make...
User Guide - Page 8
...use the Belkin software. 1. Open the Control Panel by clicking "Start", then "Control Panel". 2. In the Control Panel, click on "Network and Internet Connections".
wireless networking
3. In the next window, click on "Network Connections".
4. The "Network Connections" window will now be open. Double-click on the icon labeled "Wireless Network Connection (Belkin 11Mbps Wireless Desktop Network Card...
User Guide - Page 9
... bottom right-hand corner of your computer screen. The "Belkin Wireless LAN Utility" window will open. You will see the "Link Status" tab. There are four tabs that perform different functions.
7. Click "OK".
8. Windows XP is now configured to let the Belkin software control the
Card. Follow the directions in the next section titled "Windows 98, Me,
2000" to operate the...
User Guide - Page 10
...the wireless network. State Display This field shows you if the Card is connected to a wireless network or if it is searching for a wireless network. There are two states:
wireless networking
Associated: The Card is connected to a wireless network. The numbers following the word "Associated" refer to the MAC address of the wireless access point that the Card is connected to. Scanning: The Card is...
User Guide - Page 11
... each location and name them for easy identification. The "default" profile will contain the initial configuration setting when you install the Card. In Ad-Hoc mode, each wireless device will use the same SSID to create a small wireless network. For instance, if you want to connect a PDA to a PC, then both must have the same SSID such...
User Guide - Page 14
...powerful and secure; 128-bit encryption is very powerful...the Internet, downloading files...digit numbers (called "hexadecimal"). In Infrastructure mode, where an access point or wireless router is being used, the access point or wireless router is programmed with an encryption key. For a wireless device to join the wireless network, the same encryption key must be programmed into the device. Your Card...
User Guide - Page 15
...of the signal expressed in dBm. Link Quality: displays the link quality (Excellent, Fair, Poor, Not Connected). Channel: displays the operating channel of the wireless network. Network Address: displays the MAC address of the wireless network's access point. Clicking on the "Scan" button will rescan the area for wireless networks. To join a wireless network that you see in the Site Monitor, double...
User Guide - Page 16
... Desktop PCI Network Adapter
wireless networking
Infrastructure Network (Access Point)
The use of a wireless access point to connect a wireless LAN to a wired LAN is called Infrastructure mode. A wireless access point serves as a bridge between the wired and wireless network. Connecting the access point to any port on the wired network will give wireless access to all wireless-equipped computers...
User Guide - Page 19
... network is considered a LAN. MAC Address: MAC stands for Media Access Control. A MAC address is the hardware address of a device connected to a network. A MAC address is unique (different) for every device. NAT: Network Address Translation. This process allows all of the computers on your home network to use one IP address. Using the NAT capability of the Belkin 4-Port Cable/DSL Gateway Router...
User Guide - Page 20
... the
receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. 34
wireless networking
Modifications
The FCC requires the user to be notified that any changes or modifications to this device that are not expressly approved by Belkin Components may void the users authority to operate the equipment.
Canada- Industry...