Brother International XL-5700 driver and firmware
Drivers and firmware downloads for this Brother International item
Related Brother International XL-5700 Manual Pages
Download the free PDF manual for Brother International XL-5700 and other Brother International manuals at ManualOwl.com
Users Manual - English - Page 8
...servicing...install the proper outlet. Do not modify the plug in any way.
Foot Controller
When you press the foot controller...controller, otherwise a fire or an electric shock could occur.
Note
(For U.S.A. only) ● Foot Controller: Model KD-1902
This foot controller can be used with Models XL-5500/XL-5600/XL-5700/ XL-5510/XL-5610/XL-5710.
.
Inserting the Needle
CAUTION
● Turn the main power...
Users Manual - English - Page 9
... needle bar to its highest position.
2
Lower the presser foot.
3
If a needle is already installed, remove it by 4 loosening the needle clamp with a
screwdriver and pulling the needle down.
1...Changing the Presser Foot
CAUTION
● Always turn off the power before you change the presser foot. If you leave the power on and step on the controller, the machine will start and you may be injured.
...
Users Manual - English - Page 10
... the front right-hand side of the base plate to adjust it until the machine is stable.
CAUTION
● If the presser foot is not installed with the correct orientation, the needle may strike the presser foot, which may bend or break the needle and cause injury.
9
Users Manual - English - Page 33
...1
1 Front of chalk mark 2 Red lines
CAUTION
● If the presser foot is not installed with the correct orientation, the needle may strike the presser foot, bending or breaking the needle and...
to cut through any stitches.
Step
Step 1 (Front bar tack)
Sewn section
a
Pattern
a/c c
a
1. Set the pattern selection dial to "a". 2. Lower the presser foot and sew 5 to 6 stitches. 3. Stop the machine...
Users Manual - English - Page 39
... screw.
5
Loosen the face plate screw.
2
Remove the face plate from the machine as 3 shown below.
Oiling
Remove the power supply plug from the 1 outlet.
Remove the needle plate and the face plate, 2 and then put 2 to 3 drops of....
4
1 2
3
1 Bulb 2 Loosen 3 Tighten
Operate the machine at a fast speed for a 3 short time without thread installed.
Be sure to wipe any excess oil off the 4 machine.
38
Users Manual - English - Page 40
... the hook by grasping its center post 5 and pulling it out.
3 5
2
4
1
1
1 Retaining ring 2 Latch lever 3 Hook 4 Driver 5 Race body
■ Cleaning the Shuttle Race Remove any accumulated lint and thread from
1 the retaining ring, hook, driver and race body with a brush.
Wipe lint from the shuttle race using a cloth 2 dampened with machine...
Users Manual - English - Page 41
...difficulties are encountered, first review the manual section about the operation that you... improve the operation. If you still have difficulties, contact your nearest service center.
UPPER THREAD BREAKS
LOWER THREAD BREAKS
SKIPPED STITCHES
LOOP IN SEAM...fabric is incorrect.
Page 24 No
Spool of thread is not correctly installed.
Lower threading is not correct.
Lint is clinging to the bottom ...
Accessory Catalog - Page 5
...guide screw, adjust the fabric guide to the edge of the fabric, and lower
the presser foot. 3. Sew.
SA133 ABCDEFJKMN
SA134 GHILOP
SA128 All Brother home-use sewing machines
Concealed Zipper Foot
Allows you to install.... 2. Place the fold at the left side of the center guide. 3. Sew and open the fabric.
SA184 All Brother home-use sewing machines
Ring Bearer Pillow & Hankerchief
Innov-is Project...
Accessory Catalog - Page 7
... be used with all Brother presser feet. Can be used for stitching heavy fabrics together.
1. Attach the seam guide on the needle plate with the thumbscrew of the seam guide. 2. Adjust the distance...stitching especially on thin fabrics or small pieces of patchworks. Installing the Straight Stitch Needle Plate automatically sets the needle position to the center straight stitching position on selected...
Accessory Catalog - Page 13
....)
Brother Embellishment
Feet
Pin Tuck Foot
24
Ruffler Foot
Pin Tuck Foot
This presser foot has 7 grooves and produces perfect pin tucks and corded pin tucks using a twin needle on lightweight fabric. A specially designed bobbin cover is also included with this presser foot.
1. Install and manually thread a twin needle. 2. Draw a reference line to guide...
Accessory Catalog - Page 16
... own unique embroidery patterns in the easy steps. Comes with USB card writer, 4M blank memory card and software compatible with Windows 2000 or later. SAVR8.0 Upgrade kit is compatible with PE-DESIGN 5.0, 6.0 & 7.0.
PE-DESIGN® Lite
New to embroidery software? Master basic digitizing and embroidery design work with Brother's easy to use PE-DESIGN® Lite.
PE-DESIGN®...
Accessory Catalog - Page 17
... QuattroTM 6000D
SAVR4000D Innov-is 4000D
QuattroTM 6000D Embroider y Card Reader
Connect your embroidery card reader using the built-in USB port on your QuattroTM 6000D. This Embroidery Card Reader is compatible with the entire library of Brother Embroidery Cards, including licensed content. The simple and easy USB attachment takes seconds to connect and ensures your treasured collection...