Dell PowerConnect 3424P driver and firmware
Drivers and firmware downloads for this Dell item
Related Dell PowerConnect 3424P Manual Pages
Download the free PDF manual for Dell PowerConnect 3424P and other Dell manuals at ManualOwl.com
Command
Line Interface (CLI) Guide (.htm) - Page 23
... keyboard and the textual output displays via a terminal monitor. You can access the CLI from a VT100 terminal connected to the console port of the device or through a Telnet connection from a remote host.
The first time you use the CLI from the console a Setup Wizard is invoked. The Setup Wizard guides you in setting up a minimum configuration, so that...
Command
Line Interface (CLI) Guide (.htm) - Page 34
... set should be transmitted.
Specifies the management address that would be advertised from an interface.
Restarts the LLDP RX state machine and clears the neighbors table. Displays the Link Layer Discovery Protocol (LLDP) configuration. Displays the Link Layer Discovery Protocol (LLDP) information that is advertised from a specific port. Displays information about discovered neighboring devices...
Command
Line Interface (CLI) Guide (.htm) - Page 68
www.dell.com | support.dell.com
NOTICE: When using HyperTerminal with Microsoft® Windows 2000,ensure that Windows® 2000 Service Pack 2 or later is installed.With Windows 2000 Service Pack 2, the arrow keys function properly in HyperTerminal's VT100 emulation. Go to www.microsoft.com for information on Windows 2000 service packs.
For more information, see Dell™ PowerConnect™ ...
Command
Line Interface (CLI) Guide (.htm) - Page 216
... blocked ports. If a port is controlled by 802.1X, LLDP operates only if the port is authorized.
Examples The following example enables Link Layer Discovery Protocol (LLDP) on an interface (g5).
Console(config)# interface ethernet 1/e5
Console(config-if)# lldp enable
lldp timer
To specify how often the software sends Link Layer Discovery Protocol (LLDP) updates, use...
Command
Line Interface (CLI) Guide (.htm) - Page 217
... often the software sends Link Layer Discovery Protocol (LLDP) updates.
Console (config) # lldp timer
lldp hold-multiplier
To specify the amount of time, the receiving device should hold a Link Layer Discovery Protocol (LLDP) packet before discarding it. Use the lldp hold-multiplier command in global configuration mode. To revert to the default setting, use...
User's Guide
(.htm) - Page 5
... a DHCP Server 65 Receiving an IP Address From a BOOTP Server 66 Security Management and Password Configuration 67
Startup Procedures 70 Startup Menu Procedures 70 Software Download Through TFTP Server 73
Port Default Settings 76 Auto-Negotiation 76 MDI/MDIX 76 Flow Control 76 Back Pressure 76 Switching Port Default Settings 77
5 Using Dell OpenManage Switch Administrator
Starting the...
User's Guide
(.htm) - Page 22
... | support.dell.com
PowerConnect 3448
The PowerConnect 3448 provides 48 10/100Mbps ports plus two SFP ports, and two Copper ports which can be used to forward traffic in a stand-alone device, or as stacking ports when the device is stacked. The device also provides one RS-232 console port. The PowerConnect 3448 is a stackable device, but also functions as a stand-alone device.
PowerConnect 3448P...
User's Guide
(.htm) - Page 28
... of all updated device features, see the latest software version Release Notes.
Power over Ethernet
Power over Ethernet (PoE) provides power to devices over existing LAN cabling, without updating or modifying the network infrastructure. PoE removes the need for placing network devices next to power sources. PoE can be used in the following applications: • IP Phones • Wireless Access...
User's Guide
(.htm) - Page 34
... The device supports boot image, software, and configuration upload/download via TFTP.
Remote Monitoring Remote Monitoring (RMON) is an extension to SNMP, which provides comprehensive network traffic monitoring capabilities (as opposed to SNMP which allows network device management and monitoring). RMON is a standard MIB that defines current and historical MAC-layer statistics and control objects...
User's Guide
(.htm) - Page 57
... DB-9 connector for the Console port and the appropriate connector for the terminal
To connect a terminal to the device Console port:
1 Connect the supplied RS-232 crossover cable to the terminal running VT100 terminal emulation software.
2 Select the appropriate serial port (serial port 1 or serial port 2) to connect to the console.
Installing the PowerConnect 3424/P and PowerConnect 3448/P
57
User's Guide
(.htm) - Page 70
...power on and watch for the auto-boot message SYSTEM RESET Boot1 Checksum Test PASS Boot2 Checksum Test PASS Flash Image Validation Test PASS BOOT Software Version 1.0.0.05 Built 06-Jan-2005 14:46:49 Carrier board...using the ASCII terminal or Windows HyperTerminal.
[1] Download Software
[2] Erase Flash File
[3] Password Recovery Procedure
[4] Enter Diagnostic Mode
[5] Set Terminal Baud-Rate
[6] ...
User's Guide
(.htm) - Page 71
...[1] The software download procedure is performed when a new version must be downloaded to replace the corrupted files, update or upgrade the system software. To download software from the Startup menu:
1 From the Startup menu, press [1]. The following prompt appears: Downloading code using XMODEM Running SW Ver. 1.0.0.30 Date 09-Jan-2005 Time 14:30:02 HW version is Base Mac address is : 00...
User's Guide
(.htm) - Page 75
... the TFTP server and programming it into the flash updates the boot image. The boot image is loaded when the device is powered on. A user has no control over the boot image copies. To download a boot image through the TFTP server:
1 Ensure that an IP address is configured on one of the device ports and pings can be sent to a TFTP...
User's Guide
(.htm) - Page 212
... are added to the commands existing in the Running Configuration file. To update the Startup Configuration file, before powering down the device, the Running Configuration file must be copied to the Startup Configuration file.
• Backup Configuration File - Contains a backup copy of the device configuration. Up to five backup configuration files can be saved on the...
User's Guide
(.htm) - Page 213
... two Flash Files called Image 1 and Image 2. The active image stores the active copy, while the other image stores a second copy. The device boots and runs from the active image. If the active image is corrupted, the system automatically boots from the non-active image. This is a safety feature for faults occurring during the Software Upgrade...
User's Guide
(.htm) - Page 214
www.dell.com | support.dell.com
Destination File Name - The destination file type to which the file is downloaded. The possible field values are:
Software Image - Downloads the Image file.
Boot Code - Downloads the Boot file.
Configuration Download TFTP Server IP Address - The TFTP Server IP Address from which the configuration files are downloaded.
Source File Name - Indicates the configuration ...
User's Guide
(.htm) - Page 399
...ACL, 241 Address Resolution
Protocol, 149, 387 Address tables, ...settings, 220 Defining device
information, 88 Defining MAC-Based
ACLs, 241 Device installation, 50 Device representation, 81 Device view, 80 DHCP, 33 Dimensions, 40 DNS, 34, 142 Domain Name System, 34, 142 Downloading software, 212 DSCP, 373, 390 Dynamic Address Table, 269
E
EAP, 35, 225 Emergency, 124 Enable, 164, 180 EPG, 390 Error...
User's Guide Addendum
(.pdf) - Page 4
...20
Release Date November, 2006
The firmware image version should be 2.0.0.20 on the PowerConnect 3424/3448/3424P/3448P. The boot prom image should be 1.0.1.01 Refer to the PowerConnect 34XX Systems User's Guide for instructions on loading the boot PROM software and updating the firmware image.
Version number
3424/3448/
20 0
3424p/3448P
Version Numbering Convention
Description
20 Four part...
User's Guide Addendum
(.pdf) - Page 5
... / Download of Configuration Files • HTTP/S Upload of Software Image
Issues resolved
The following is a list of issues resolved in the current firmware release.
Title Management Station Loses Communication to Stack after Master Unit Failure.
Configuration file with PVLAN cannot be copied to startup. Native VLAN display.
Display of configured LACP Channels.
WBI Stacking Port Information...
User's Guide Addendum
(.pdf) - Page 7
...in the Dell PowerConnect 34xx Systems User's Note: The phrase "the device" herein after is used to refer to the PowerConnect 34xx Series switches.
Corrections and Additions to the User's Guide and CLI Reference Guide
Corrections and Additions to the User's Guide
Web Screen / Section in Guide
Configuring Switch Information -> Configuring VLANs -> Defining VLAN Ports Settings
(RN34666)
Configuring...