Dell PowerConnect 6248P driver and firmware
Drivers and firmware downloads for this Dell item
Related Dell PowerConnect 6248P Manual Pages
Download the free PDF manual for Dell PowerConnect 6248P and other Dell manuals at ManualOwl.com
Command Line Interface Guide - Page 55
...describes the command functionality.
This guide also provides information for configuring the PowerConnect switch, details the procedures, and provides configuration examples. Basic installation configuration is described in the User's Guide and must be completed before using this document.
Command Groups
The system commands can be broken down into three sets of functional groups, Layers 2, Layer...
Command Line Interface Guide - Page 176
... MEM: 266.666664 MHz, PCI: 66.666666 MHz, CPU: 533.333328 MHz PCI unit 0: Dev 0xb314, Rev 0x01, Chip BCM56314_A0, Driver BCM56314_A0 SOC unit 0 attached to PCI device BCM56314_A0 Adding BCM transport pointers Configuring CPUTRANS TX Configuring CPUTRANS RX Instantiating /download as rawFs, device = 0x20001 Formatting /download for DOSFS Instantiating /download as rawFs, device = 0x20001 Formatting...
Command Line Interface Guide - Page 423
...: True
Media Policy Application Type : streamingvideo Vlan ID: 20 Priority: 1 DSCP: 2 Unknown: False Tagged: True Inventory Hardware Rev: xxx xxx xxx Firmware Rev: xxx xxx xxx Software Rev: xxx xxx xxx Serial Num: xxx xxx xxx Mfg Name: xxx xxx xxx Model Name: xxx xxx xxx Asset ID: xxx xxx xxx
Location Subtype...
Command Line Interface Guide - Page 426
Network Policies Media Policy Application Type : voice Vlan ID: 10 Priority: 5 DSCP: 1 Unknown: False Tagged: True
Media Policy Application Type : streamingvideo Vlan ID: 20 Priority: 1 DSCP: 2 Unknown: False Tagged: True
Inventory Hardware Rev: xxx xxx xxx Firmware Rev: xxx xxx xxx Software Rev: xxx xxx xxx Serial Num: xxx xxx xxx Mfg Name: xxx xxx...
Command Line Interface Guide - Page 893
...neighbor for both planned and unplanned restarts
Command Mode Router OSPF Configuration mode
User Guidelines The grace LSA announcing the graceful restart includes a restart reason. Reasons 1 (software restart) and 2 (software reload/upgrade) are considered planned restarts. Reasons 0 (unknown) and 3 (switch to redundant control processor) are considered unplanned restarts. nsf ietf helper disable...
Command Line Interface Guide - Page 921
...to acknowledge.
Restart Helper Status: One of two values:
• Helping - This router is acting as a helpful neighbor to this neighbor. A helpful neighbor does not ...sent by the restarting router. Possible values for the Restart Reason are defined in RFC 3623 as follows:
- Unknown (0)
- Software restart (1)
- Software reload/upgrade (2)
- Switch to redundant control processor (3)
- Unrecognized - ...
Command Line Interface Guide - Page 963
... announcing the graceful restart includes a restart reason. Reasons 1 (software restart) and 2 (software reload/upgrade) are considered planned restarts. Reasons 0 (unknown) and 3 (switch to redundant control processor) are considered unplanned restarts. nsf ietf helper disable is functionally equivalent to no nsf helper and is supported solely for IS CLI compatibility.
Example -
nsf helper strict...
Getting Started Guide - Page 7
... basic information to install, configure, and operate Dell™ PowerConnect™ PC6224, PC6248, PC6224P, PC6248P, and PC6224F systems. For more information, see the User's Guide, which is available on your User Documentation CD, or check the Dell Support web site at support.dell.com for the latest updates on documentation and firmware.
Site Preparation
PowerConnect 6200 series switches...
Getting Started Guide - Page 9
...
1 Connect the supplied RS-232 cable to a VT100 terminal or to the serial connector of a personal computer running VT100 terminal emulation software.
2 Connect the female DB-9 connector at the other end of the RS-232 crossover cable to the serial port connector on the rear of the switch.
NOTE: If you are installing a stack of switches, connect the...
Getting Started Guide - Page 12
...: If you are installing a stack of switches, you need to assemble and cable the stack before powering up and configuring the stack.
1 Connect an RS-232 crossover cable to the terminal running VT100 terminal emulation software. 2 Configure the terminal emulation software as follows:
a Select the appropriate serial port (serial port 1 or serial port 2) to connect to the console. b Set the data rate...
Getting Started Guide - Page 13
3 Connect the female connector of the RS-232 crossover cable directly to the switch console port, and tighten the captive retaining bolts. The PowerConnect 6200 series console ports are located on the rear panel as shown in Figure 1-4.
NOTE: If you are installing a stack of switches, connect the terminal to the Master Switch. This switch will...
Getting Started Guide - Page 18
... information about all of the switches in the stack, including the Firmware Version, Hardware Version, Management Preference, Switch MAC Address, and Switch Serial Number. You can use the command line interface or the Web interface to view this information.
See the CLI Reference Manual and the User's Guide for assistance with the CLI and Web interface, respectively.
Auto...
Release Notes - Page 1
.../6248/6248P
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Date: May 2010 System Firmware Version 3.2.0.6
Information in this document is subject to change without notice. © 2003 - 2010 Dell Inc. All rights reserved. Reproduction in any manner whatsoever without the written permission of Dell Inc is strictly forbidden. Trademarks used in this text: Dell, the DELL logo and PowerConnect...
Release Notes - Page 3
... Site http://support.dell.com/.
Firmware Specifications
Firmware Version Details
Boot PROM Name Not Applicable
Version No. 3.2.0.6
Release Date May 2010
Firmware Upgrade
NOTE: Version 3.2 includes improvements to the firmware management system. You MUST follow the procedure set forth in the Dell PowerConnect 6200 Series Release 3.2 Upgrade Procedure included in the zip file to update the boot...
Release Notes - Page 4
... Guide and the Dell™ PowerConnect™ 6200 Series Configuration Guide.
NOTE: OMNM 4.1 will not discover the switches running any version of 3.x.y.z firmware therefore users should upgrade to version 4.2.
If you use OpenManage Network Manager to deploy firmware, do not use it to deploy 3.x (or later) firmware to a PowerConnect 62xx device that is currently running firmware version...
Release Notes - Page 5
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Added Functionality in this Release ¾ Non-Stop Forwarding
This feature creates an option to allow the forwarding plane of stack units to continue to forward packets while the control and management planes restart as a result of a power failure, hardware failure, or software fault on the stack management...
Release Notes - Page 13
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Changed Functionality in this Release
¾ Spanning Tree Update - 802.1Q-2005
Spanning Tree now supports IEEE802.1Q-2005. This version of the IEEE Multiple Spanning Tree Protocol corrects problems associated with the previous version, provides for faster transition-to-forwarding, and incorporates new features for a port (restricted role and...
Release Notes - Page 15
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
¾ Trap Configuration
In previous versions of the software, configuration of the flags for controlling traps was scattered about in a number of places. snmp-server enable traps is now a common command for configuring all trap flags. The legacy commands are ...
Release Notes - Page 22
... Two copies of DLF/Bcast/Unknown unicast packet will be sent out of the port 1 to 24 if two PC6248 switches are stacked using both the stack ports to form stack trunk.
Resolution
Correct the API to properly set the RADIUS...the portfast was being applied even on trunk switchports. Modified the driver layer to ignore this trunk-id while destroying external trunks.
20
System Firmware Version 3.2.0.6
Release Notes - Page 27
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Known Issues
Summary Non-configuration file getting loaded to startup-config through HTTP. TACACS operation
Ping fails with 33% to 100% packet loss OSPF Dead interval expires on neighbor, when the DUT stack manager restarts with large configuration.
VLAN configuration is not successful on ports after detaching...