Dell PowerEdge 350 driver and firmware
Related Dell PowerEdge 350 Manual Pages
Download the free PDF manual for Dell PowerEdge 350 and other Dell manuals at ManualOwl.com
Microprocessor
Upgrade Installation Guide - Page 3
... replace a microprocessor, check the latest system BIOS information on the Dell Support website at support.dell.com, and upgrade the BIOS if necessary.
Each microprocessor and its associated cache memory are contained in a pin-grid array (PGA) package that is installed in a ZIF socket on the system board. The following subsection describes how to install or replace the microprocessor in either...
Microprocessor
Upgrade Installation Guide - Page 4
www.dell.com | support.dell.com
4 If you are upgrading an existing microprocessor, remove the microprocessor heat sink.
NOTE: If a cooling fan is mounted on the heat sink, you can ... microprocessor.
7 Unpack the new microprocessor.
If any of the pins on the microprocessor appear bent, see "Getting Help" in your Installation and Troubleshooting Guide.
1-2
Microprocessor Upgrade Installation Guide
Microprocessor
Upgrade Installation Guide - Page 5
...Align pin 1 on the microprocessor with pin 1 on the microprocessor socket.
c With pin 1 of the microprocessor and socket aligned, set the microprocessor lightly in the socket and ensure that all pins are matched with the correct holes in the socket.
Because the system...lever back down until it snaps into place, locking the microprocessor in the socket.
Microprocessor Upgrade Installation Guide
1-3
Microprocessor
Upgrade Installation Guide - Page 6
....dell.com | support.dell.com
9 Install ...mark on the system board, if applicable.
10 Orient the heat-sink retention clip as shown in your Installation and Troubleshooting Guide.
11 Hook the ... upgrade kit, replace the primary VRM already installed in the system with one of the VRMs from the upgrade kit.
NOTE: The system does not support mismatched VRMs.
1-4
Microprocessor Upgrade Installation Guide
Microprocessor
Upgrade Installation Guide - Page 7
... stored in the system's nonvolatile random-access memory (NVRAM). To clear this message log, see your systems management software documentation.
18 Enter the System Setup program and ensure that the microprocessor categories match the new system configuration. For instructions about using the System Setup program, see your User's Guide.
19 Run the system diagnostics to verify...
Microprocessor
Upgrade Installation Guide - Page 34
www.dell.com | support.dell.com
2 Installation and Troubleshooting Guide
3 Installation and Troubleshooting Guide
4
Installation and Troubleshooting Guide
a
b Installation and Troubleshooting Guide
5 5-1
6
5-2
Microprocessor
Upgrade Installation Guide - Page 35
7
Installation and Troubleshooting Guide
図 5-1
ピン 1
ZIF
8 5-1
a
b 1 1
5-3
Microprocessor
Upgrade Installation Guide - Page 36
www.dell.com | support.dell.com
c 1
ZIF
d
9
10 『Installation and Troubleshooting Guide
11
12 ZIF
Installation and Troubleshooting Guide
13
5-4
Microprocessor
Upgrade Installation Guide - Page 37
14 VRM VRM a VRM VRM b VRM VRM 5-2 c VRM が 2 VRM VRM の 1 VRM
図 5-2. VRM
VRM
VRM
ラッチ（2）
15 Installation and Troubleshooting Guide
16 Installation and Troubleshooting Guide
5-5
Microprocessor
Upgrade Installation Guide - Page 38
www.dell.com | support.dell.com
17
NVRAM RAM
18
19 Installation and Troubleshooting Guide
5-6
Information Update - Page 28
• 80 x 26
•
•
:
Microsoft® Windows® HyperTerminal
Windows
9600
http://www.hillgrave.com 1
ANSI ( 19.2 KB 57.6 KB
) 115.2 KB/
HyperTerminal
Dell
HyperTerminal
HyperTerminal
2
Hit if you want to run setup
:
[BIOS Setup Utility]
: 3 4 [Serial Features]
[System Management]
5-2
Information Update - Page 29
... Redirection]
6 [Enabled]
7
:
(Windows HyperTerminal )
8 9
10 [Yes]
Dell
Dell Windows NT®
Microsoft Windows 95 Windows 98 Dell OpenManage Server Assistant CD
:
and Troubleshooting Guide
Dell
PXE (Preboot Execution Environment)
PXE (Preboot Execution Environment)
Dell PowerEdge 350 Systems Installation
: PowerEdge 350 PXE
1
PXE
1
2
Hit if you want to run setup
5-3
Memory Module
Installation Information Update - Page 5
...174; Pentium® microprocessor or a 700-MHz or higher Celeron™ microprocessor.
When replacing or installing a memory module in the DIMM3 socket on your system board, you must first remove the heat sink from the microprocessor.
To remove heat sink, perform the following...opposite side of the socket.
2. Lift the heat sink away from the microprocessor.
support.dell.com
Information Update 1-1
Memory Module
Installation Information Update - Page 6
... in the DIMM3 socket on the system board. For instructions on replacing or installing memory modules, see "Memory Modules" in your Installation and Troubleshooting Guide.
1. Place the heat sink on the microprocessor. &#...into the heat sink's center groove with the heat sink clip thumb tab facing away from the memory module sockets.
3. Hook the end of the heat-sink clip without the thumb pad into the...
Memory Module
Installation Information Update - Page 22
DIMM3
DIMM3
bleshooting Guide
1. • •
ZIF zero insertion force 2. 3. 4.
Installation and Trou-
ZIF ZIF
5-2
System Diagnostics
Information Update - Page 1
System Diagnostics Information Update
When the 850-megahertz (MHz) microprocessor is installed and the system diagnostics are run, floating point unit (FPU) exception errors are sometimes generated. These are false errors and should be ignored.
Information in this document is subject to change without notice. © 2001 Dell Computer Corporation. All rights reserved. Printed in the U.S.A.
...
Rack
Installation Guide - Page 1
Dell™ PowerEdge™ 100 and 110 Appliances and PowerEdge™ 350 Systems
RACK INSTALLATION GUIDE
www.dell.com support.dell.com
Rack
Installation Guide - Page 3
... appliances are considered to be components in a rack. Thus, "component" refers to any server, storage system, or appliance, as well as to various peripherals or supporting hardware. WARNING: Installing Dell system components in a Dell rack without the front and side stabilizers installed could cause the rack to tip over, potentially resulting in bodily injury under certain...
Rack
Installation Guide - Page 4
...Dell's servers, storage systems, and appliances are certified as components for use in Dell's rack cabinet using the Dell customer rack kit. The final installation of Dell...installed in a Dell rack by trained service tech-
nicians. If you install the kit in any other rack, be sure that the rack meets the specifications of a Dell... that provides power to the rack. The
total rack load should not exceed...
Rack
Installation Guide - Page 24
... Rack Unit For more information about requirements for installing components in a rack, see the Dell Rack Advisor software available on the Dell World Wide Web site at http://support.dell.com. WARNING: If you are installing more than one system, install the slide assemblies so that the first system is installed in the lowest available position in the rack...