Seagate ST3600957SS driver and firmware
Related Seagate ST3600957SS Manual Pages
Download the free PDF manual for Seagate ST3600957SS and other Seagate manuals at ManualOwl.com
Cheetah 15K.5 SAS Product Manual - Page 58
... used by the drive to control its operation. A Mode Select command can be used to change the values identified as changeable values. Originally, current values are installed from saved or default values after a power on reset, hard reset, or Bus Device Reset message.
4. Changeable values
Changeable values form a bit mask, stored in nonvolatile memory, that dictates which...
Cheetah 15K.5 FC Product Manual - Page 16
... FC-AL controller • Concurrent dual port transfers • Support for FC arbitrated loop, private and public attachment • Differential copper FC drivers and receivers • Downloadable firmware using the FC-AL interface • Supports SCSI enclosure services via interface connector • 128-deep task set (queue) • Supports up to 32 initiators • Drive selection ID...
Cheetah 15K.5 FC Product Manual - Page 67
... used by the drive to control its operation. A Mode Select command can be used to change the values identified as changeable values. Originally, current values are installed from saved or default values after a power on reset, hard reset, or Bus Device Reset message.
4. Changeable values
Changeable values form a bit mask, stored in nonvolatile memory, that dictates which...
Cheetah 15K.5 FC Product Manual - Page 86
... 64 SCA device connector, illustrated 65 selective reset 63 FCC rules and regulations 3 FCP for SCSI, document 5 response codes 48 task management functions 48 FC-PH document 5 features 8 interface 47 Fibre Channel documents 5 Fibre Channel Interface Control page (19h) 55
Fibre Channel Interface Manual 1, 3
Fibre Channel Services 47 Field pointer bytes command 54 firmware 8
corruption 57...
Cheetah 15K.5 FC Product Manual - Page 87
... defects/errors 39 internal drive characteristics 11 IRAW 42
J
J1 connector 43 Jumper settings page command 54 jumpers 43
L
latency
average rotational 11, 12
LBdata 56 LED driver signals 72 Link Service Reject (LS_RJT) 47 link services supported 47 Lock-unlock-cache command 56 Log select command 56 Log sense command 56 logic power 67 logical block address 13...
Cheetah 15K.7 FC Product Manual - Page 4
...39 9.7 Authenticated firmware download 39 9.8 Power requirements 39 9.9 Supported commands 39
10.0 Defect and error management 40
10.1 Drive internal defects/errors 40 10.2 Drive error recovery procedures 40 10.3 FC-AL system errors 42 10.4 Background Media Scan 43 10.5 Media Pre-Scan 43 10.6 Deferred Auto-Reallocation 43 10.7 Idle Read After Write 44
11.0 Installation 45
11.1 Drive ID...
Cheetah 15K.7 FC Product Manual - Page 13
... FC-AL controller • Concurrent dual port transfers • Support for FC arbitrated loop, private and public attachment • Differential copper FC drivers and receivers • Downloadable firmware using the FC-AL interface • Supports SCSI enclosure services via interface connector • 128-deep task set (queue) • Supports up to 32 initiators • Drive selection ID...
Cheetah 15K.7 FC Product Manual - Page 44
... the appropriate credentials when the drive has been removed from its cabinet and installed in another system.
When the drive is shipped from the factory, the firmware download port is locked and the drive will reject any attempt to download new firmware. The drive owner must use the SID credential to unlock the firmware download port before firmware updates will be accepted.
9.5
Data bands...
Cheetah 15K.7 FC Product Manual - Page 66
... used by the drive to control its operation. A Mode Select command can be used to change the values identified as changeable values. Originally, current values are installed from saved or default values after a power on reset, hard reset, or Bus Device Reset message.
4. Changeable values
Changeable values form a bit mask, stored in nonvolatile memory, that dictates which...
Cheetah 15K.7 FC Product Manual - Page 83
...for SCSI, document 5 response codes 49 task management functions 49
FC-PH document 5 FDE features 7 features 7
interface 48 Fibre Channel documents 5 Fibre Channel Interface Control page (19h) 55
Fibre Channel Interface Manual 2, 3
Fibre Channel Services 48 Field pointer bytes command 55 FIPS 36 firmware 7
corruption 58 Firmware download option command 57 firmware download port 38 Firmware numbers...
Cheetah 15K.7 SAS Product Manual - Page 4
...Authenticated firmware download 37 9.8 Power requirements 38 9.9 Supported commands 38
10.0 Defect and error management 39
10.1 Drive internal defects/errors 39 10.2 Drive error recovery procedures 39 10.3 SAS system errors 41 10.4 Background Media Scan 41 10.5 Media Pre-Scan 42 10.6 Deferred Auto-Reallocation 42 10.7 Idle Read After Write 42
11.0 Installation 43
11.1 Drive orientation...
Cheetah 15K.7 SAS Product Manual - Page 43
... the appropriate credentials when the drive has been removed from its cabinet and installed in another system.
When the drive is shipped from the factory, the firmware download port is locked and the drive will reject any attempt to download new firmware. The drive owner must use the SID credential to unlock the firmware download port before firmware updates will be accepted.
9.5
Data bands...
Cheetah 15K.7 SAS Product Manual - Page 57
... used by the drive to control its operation. A Mode Select command can be used to change the values identified as changeable values. Originally, current values are installed from saved or default values after a power on reset, hard reset, or Bus Device Reset message.
4. Changeable values
Changeable values form a bit mask, stored in nonvolatile memory, that dictates which...
Cheetah 15K.7 SAS Product Manual - Page 72
... engine 36 encryption key 37 environment 43 environmental
limits 29 requirements 13 environmental control 33 EraseMaster 36 error management 39 rates 13 errors 39
F
FCC rules and regulations 3 features 7
interface 45 feed forward equalizer 63 FFE 63 FIPS 35 firmware 7
corruption 49 firmware download port 37 flawed sector reallocation 7 Format command execution time 10 function
complete, code...
Cheetah 15K.6 FC Product Manual - Page 14
... port FC-AL controller
• Concurrent dual port transfers
• Support for FC arbitrated loop, private and public attachment
• Differential copper FC drivers and receivers
• Downloadable firmware using the FC-AL interface
• Supports SCSI enclosure services via interface connector
• 128-deep task set (queue)
• Supports up to 32 initiators
• Drive...
Cheetah 15K.6 FC Product Manual - Page 69
... used by the drive to control its operation. A Mode Select command can be used to change the values identified as changeable values. Originally, current values are installed from saved or default values after a power on reset, hard reset, or Bus Device Reset message.
4. Changeable values
Changeable values form a bit mask, stored in nonvolatile memory, that dictates which...
Cheetah 15K.6 FC Product Manual - Page 89
... defects/errors 43 internal drive characteristics 11 IRAW 46
J
J1 connector 47 Jumper settings page command 58 jumpers 47
L
latency
average rotational 11, 12
LBdata 60 LED driver signals 76 Link Service Reject (LS_RJT) 51 link services supported 51 Lock-unlock-cache command 59 Log select command 60 Log sense command 60 logic power 71 logical block address 13...
Cheetah 15K.6 SAS Product Manual - Page 62
... used by the drive to control its operation. A Mode Select command can be used to change the values identified as changeable values. Originally, current values are installed from saved or default values after a power on reset, hard reset, or Bus Device Reset message.
4. Changeable values
Changeable values form a bit mask, stored in nonvolatile memory, that dictates which...
Cheetah 15K.5 SCSI Product Manual - Page 13
...; Self diagnostics performed when power is applied to the drive • Zoned bit recording (ZBR) • Vertical, horizontal, or top down mounting • Dynamic spindle brake • 16,384 kbytes data buffer • Hot plug compatibility (Section 10.6.4.2 lists proper host connector needed) for LC model drives • Drive Self Test (DST) • Supports SCSI bus fairness
4.2
Media...
Cheetah 15K.5 SCSI Product Manual - Page 57
... being used by the drive to control its operation. A Mode Select command can be used to change these values (only those that are changeable). Originally, they are installed from saved or default values after a power on reset, hard reset, or Bus Device Reset message.
Changeable values form a bit mask, stored in nonvolatile memory, that dictates which of...