Acer AT350 F3 driver and firmware
Drivers and firmware downloads for this Acer Computers item
Related Acer AT350 F3 Manual Pages
Download the free PDF manual for Acer AT350 F3 and other Acer manuals at ManualOwl.com
User Manual - Page 2
System setup
System notes
Thank you for purchasing your Acer server. This user guide is intended as a reference for experienced server technicians and helps detail many of the features available in Acer servers. For more detailed information about any particular component or software solution, you may consult the technical specifications or the user manuel for that...
User Manual - Page 4
... the system is operating. Indicates hard disk drive activity when flashing.
LAN1 Network Activity LED LAN2 Network Activity LED Information LED
Indicates network activity on LAN1 when flashing. Indicates network activity on LAN2 when flashing.
Power Fail
This LED functions only when two power supply modules have been installed in the system and indicates a power supply module has failed (when...
User Manual - Page 5
Setting up the system
Pre-installation requirements
Selecting a site
Before unpacking and installing the system, select a suitable site for the system for maximum efficiency. Consider the following factors when choosing a site for the system:
⚫ Near a grounded power outlet. ⚫ Clean and dust-free ⚫ Stable surface free from vibration. ⚫ Well-ventilated and away...
User Manual - Page 8
... to the related user documentation.
To turn off the system via software:
1. Press + + on the attached keyboard or click Start on the Windows taskbar.
2. Select Shut Down. 3. Select Shut Down from the... drop-down menu, then click OK.
To turn off the system via hardware
If you cannot shut down the server via software, press the power...
User Manual - Page 10
... cables correctly connected and secured? ⚫ Did you press the system power button to turn the server on (power on indicator should be lit green)? ⚫ Are all device drivers properly installed? ⚫ Are hard disk drive(s) properly formatted and configured? ⚫ Are the BIOS configuration settings in the BIOS Setup Utility correct? ⚫ Is the operating system properly loaded...
User Manual - Page 11
... on the display monitor. 6. Set the display brightness and contrast controls to at least two thirds of their maximum
range. Refer the documentation that came with your display monitor. 7. If the operating system normally loads from the hard drive, make sure there is no diskette in floppy drive and no disc in the optical drive. 8. If the power indicator is lit...
User Manual - Page 12
... that you have installed system compliant processors, and that they are populated according to the system guidelines.
HDD activity indicator does not light.
Do the following:
⚫ Make sure the drive is not disabled in the BIOS Setup Utility. ⚫ Make sure the drive is compatible ⚫ Make sure you have not exceeded the power budget for...
User Manual - Page 13
... and jumpers on the hard drive and on the backplane board are set correctly.
Optical drive activity indicator does not light
Do the following:
⚫ Make sure the SATA and power cables are properly connected. ⚫ Check that relevant switches and jumpers on the drive are set correctly. ⚫ Check that the drive is properly configured.
Optical drive tray cannot be ejected Insert...
User Manual - Page 14
... came with the device
There is problem with the software program.
Do the following:
⚫ Verify that the software is properly configured for the system. ⚫ Refer to the software installation and operation documentation for instructions on
setting up and using the software. Try a different version of the software to see if the problem is with the copy you are using...
User Manual - Page 16
... cloth for cleaning.
CAUTION for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to the power supply unit:
⚫ Install the power supply unit before connecting the power cord to the AC power outlet. ⚫ Unplug the power cord before removing the power supply unit from the computer. ⚫ If the system has multiple sources...
User Manual - Page 21
...an experienced radio/television technician for help
Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. In compliance with FCC regulations, use shielded cables to connect to other computing devices.
Notice: Peripheral devices Only peripherals (input/output devices, terminals, printers, etc.) certified to...