Canon LV-S4 driver and firmware
Related Canon LV-S4 Manual Pages
Download the free PDF manual for Canon LV-S4 and other Canon manuals at ManualOwl.com
Full Line - Projectors Brochure - Page 3
... Life Warranty
KIT CONTENTS
• Projector • Power Cable • VGA Computer Cable • MAC/VGA Adapter • Wireless/Wired Remote Control (AA Batteries Included) • Wired Remote Cable • Mouse Control Cable (PS/2, Serial, and Mac) • Lens Cap • Dust Cover • Warranty Card • User's Manual
* A body only version, LV-7565F is also available. Please see...
Owners Manual - Page 3
... 7
Part Names and Functions 8
Front
8
Back
8
Bottom
8
Rear Terminal
9
Top Control
10
Remote Control Unit
11
Operating Range
11
Remote Control Unit Battery Installation
12
Installation 13
Positioning the Projector
13
Adjustable Feet
13
Connecting the AC Power Cord
14
Connecting to a Computer
15
Connecting to Video Equipment
16
Basic Operation 17
Turning On the...
Owners Manual - Page 4
... not to be used for an extended time, unplug the projector from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
CAUTION
Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75. Ne peut être utilisé dans...
Owners Manual - Page 5
... projector from wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls...
Owners Manual - Page 6
...down the projector. This projector monitors internal temperature and control the running speed of the cooling fans.
Installing the Projector in Proper Position
Install the projector properly. Improper Installation may reduce .... Do not transport the projector through a courier or transport services with this bag, otherwise the projector can be damaged. When handling the projector, do not drop, bump...
Owners Manual - Page 7
... operation. Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not...
Owners Manual - Page 8
... and Connectors t e Power Cord Connector r Exhaust Vent t Top Controls and Indicators
CAUTION
Hot air is exhausted from the exhaust vent. Do not put heat-sensitive objects near this side. r
q Air Filters
e
w Air Intake Vents
e Adjustable Feet
w
CAUTION
Hot air is exhausted from the exhaust vents. When using or installing the projector, the following precautions...
Owners Manual - Page 12
Part Names and Functions
Remote Control Unit Battery Installation
1 Remove the battery compartment lid.
2 Slide the batteries into the compartment.
3 ... ● Do not expose the remote control unit to moisture or heat. ● Do not drop the remote control unit. ● If the battery has leaked on the remote control unit, carefully wipe the case clean and install new batteries. ● Risk of...
Owners Manual - Page 13
Installation
Installation
Positioning the Projector
This projector is designed to project on a flat projection surface and can be focused from 4.3'(1.3m) - 21.3'(6.5m). Refer to the figure and the table below for the screen size and the distance between the projector...
3 To retract the adjustable feet, lift the front of the projector and pull and undo the feet lock latches. Keystone distortion of ...
Owners Manual - Page 14
... risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of the type of power being supplied. Connect the projector with all peripheral equipment before turning the projector on. (See page 15, 16 for connection.)
CAUTION
For safety, unplug...
Owners Manual - Page 15
...; VGA Cable (HDB 15 pin) (Only one cable is supplied) • Audio Cable (Mini Plug: stereo Not supplied with this projector.)
Installation
Installation
Monitor output
Audio output (Stereo)
Monitor input
External Audio Equipment
VGA cable
Audio Cable (Stereo) ✽
VGA cable
Audio output
COMPUTER / S-VIDEO / COMPONENT IN
AUDIO IN
VIDEO
AUDIO IN
AUDIO OUT SERVICE PORT (VARIABLE...
Owners Manual - Page 16
...10045;
(stereo)
External Audio Equipment Audio Input
S-Video- ComponentVGA cable✽ VGA cable ✽
VIDEO AUDIO IN
COMPUTER / S-VIDEO / COMPONENT IN
VIDEO
AUDIO IN
AUDIO OUT SERVICE PORT (VARIABLE)
COMPUTER/ S-VIDEO/
RESET
COMPONENT IN
MONITOR OUT
AUDIO OUT (VARIABLE)
✔Note:
• When connecting AUDIO OUT to external audio equipment, the projector's built-in speaker...
Owners Manual - Page 21
...
For computer source
Guide Window
Show the selected Menu of the OnScreen Menu.
PC System Menu
Used to select computer system. (p25)
Image Select Menu
Used to select an image level among Standard, High contrast, Blackboard(Green), and Custom. (p29)
Screen Menu
Used to adjust size of image. [Normal / True / Wide / Digital zoom +/-] (p31)
Setting Menu...
Owners Manual - Page 45
... again, the WARNING indicator stops blinking.
TOP CONTROL
POWER
VOL -
WARNING
LAMP REPLACE
WARNING blink red
Then check the matters below:
- Did you provide appropriate space for the projector to be ventilated? Check the installing condition to see if ventilation slots are not blocked.
- Is the projector not installed near the ventilation duct of airconditioning equipment...
Owners Manual - Page 55
Appendix
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 100 MHz of Dot Clock.
ON-SCREEN DISPLAY
RESOLUTION
VGA 1
640 x 480
VGA 2
720 x 400
VGA 3
640 x 400
VGA 4
640 x 480
VGA 5
640 x 480
VGA 6
640 x 480
VGA 7
640 x 480
MAC LC13 640 x 480
MAC 13 640 x 480
480p
--------
...
Serial Functional Specification - Page 19
...four directions)
reversal setting (status: Ceiling ON)
Unacceptable "?" [CR]
8.7. Temp Read Command
Command "CR6"[CR]
Detail
Get the temperature inside a projector. When some temperature sensors are installed in the projector, it is possible...the status is Stand BY or it is 10 seconds after Power On, depend on projectors, temperature may approach critical temperature due to ballast lamp's ...