Edimax ES-5226RS driver and firmware
Related Edimax ES-5226RS Manual Pages
Download the free PDF manual for Edimax ES-5226RS and other Edimax manuals at ManualOwl.com
Datasheet - Page 1
... cable can be up to 550 m (multi-mode fiber) or 10 kilometer (single-mode fiber).
ES-5226RS has configure QoS policy priority mode and CoS (Class of Service) configuration. QoS (Quality of Service) refers to mechanisms in the network software that make the actual determination of which packets have priority. CoS refers to feature sets, or groups of services...
Datasheet - Page 2
...Rate
Switch architecture Back-plane MAC address Flash ROM LED
Power Supply Power Consumption Operation Temp. Operation Humidity Storage Temp. Dimension Installation EMI Safety Software Feature Management Port configuration
Port Trunk LACP VLAN
QOS Class of Service
Bandwidth control
DHCP Broadcast Storm filter Port Mirror
MAC Address Filtering
Firmware Upgrade
IEEE802.3 10BASE-T IEEE802.3u 100BASE...
Manual - Page 2
Notice
The contents of this manual are based on the table below listing firmware version, software kernel version, and hardware version. If the switch functions are different from the description of the manual, please contact the local sale dealer for more information.
Firmware Version Kernel Version Hardware Version
V1.10 V1.1.5 ----------
Manual - Page 3
...digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation...installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television.../TV ...
Manual - Page 4
Content
INTRODUCTION 1
Features...1 Package Contents 1
HARDWARE DESCRIPTION 3
Physical Dimensions 3 Front Panel ...3 LED Indicators ...5
Gigabit port LED Indicator 5 Rear Panel...6 Desktop Installation 7
Attaching Rubber Pads 7 Rack-mounted Installation 7 Power On...8
NETWORK APPLICATION 9
Small Workgroup 9 Segment Uplink 10
WEB-BASED MANAGEMENT 11
About Web-based Management 11 User ...
Manual - Page 5
...17 Port Mirroring 19 Bandwidth Control 20 Broadcast Storm Control 22 VLAN Setting ...23 VLAN Member Setting (Port Based 23 VLAN Mode...25 VLAN PVID Index Setting 27 Per Port Counter 29 QoS Setting ...31 Priority Mode 32 Class of Service Configuration 33 Security Filter...35 Trunk...37 Trunk Configuration 37 Aggregation Information 39 Configuration Backup/Recovery 40 Firmware Update 41...
Manual - Page 13
Desktop Installation
Set the switch on a sufficiently large flat space with a power outlet nearby. The surface where the user put the switch should be clean, smooth, level and sturdy. Make sure there is enough clearance around the switch to allow attachment of cables, power...can prevent the switch from shock/vibration.
Rack-mounted Installation
The ES-5226RS comes with a rack-mounted kit and can be ...
Manual - Page 14
... the back of the Switch. This is especially important for enclosed rack installation.
Power On
Connect the power cord to the power socket on the rear panel of the Switch. The other side of power cord connects to the power outlet. The internal power supply of the Switch works with voltage in the range of 100-240VAC...
Manual - Page 20
System IP Configuration
User can configure the IP Settings and DHCP client function in here. „ IP Address: Manually assign the IP address that the network is using. If
DHCP function is enabled, the user doesn't need to assign the IP address. And, the network DHCP server will assign the IP address displaying in this column for the switch. The...
Manual - Page 21
... „ MAC Address: Displays the unique hardware address assigned by
manufacturer (default). „ Number of Ports: Displays how many ports there are in the switch. „ Comment: Users can fill in up to 12 characters in this field. Click the Update
button to save the comments. „ System Version: Displays the switch's firmware version „ Kernel Version: Displays the kernel version „...
Manual - Page 22
Default Switch Setting and Reboot
Reset switch to default configuration. Click Default to reset all configurations to the default value.
Factory Default interface
When you see the information as below, close the web window and launch again after a while.
Reboot in progress
16
Manual - Page 23
... Bandwidth Control, and Broadcast Storm Control.
Port Configuration
In Port Configuration, you can set and view the operation mode for each port. „ Auto-Negotiation: Enable and Disable. Being set as 'Enable', the Speed,
Duplex mode, Pause, Backpressure, TX Capability and Address Learning are negotiated automatically. When you set it as 'Disable', you have to assign those items manually. „...
Manual - Page 25
... packet is to be monitored.
„ Source Port: The ports that the user wants to monitor. All monitored port traffic will be copied to mirroring (destination) port. Users can select multiple source ports by ticking the check boxes beneath the port number label to be monitored.
„ And then, click Update to have the configuration take effect.
19
Manual - Page 27
...rate. When Speed Base is set as Low, the transmitting rate for all the ports is in the range between 32K bytes and 8M bytes. When Speed Base is set as High, the transmitting rate for port 1 ~ 24 is in ...rate. When Speed Base is set as Low, the receiving rate for all the ports is in the range between 32K bytes and 8M bytes. When Speed Base is set as High, the transmitting rate for port 1 ~ 24 Is in ...
Manual - Page 28
... defined. Each port's broadcast storm protection function can be enabled individually by ticking the check boxes.
Broadcast Storm Control interface
„...port can send or receive in a period of time.
„ Enable Port: Having ticked the boxes, the port will stop transmitting or receiving data when their sending byte counts or receiving byte counts reach the defined threshold.
„ Click Update...
Manual - Page 29
..., all the network devices are still plugged into the same switch physically.
VLAN Member Setting (Port Based)
The switch provides port based VLAN configuration. Users can enable the function via VALN member setting. That is a set of ports allowed to be forwarded from the source port. The overall number of VLAN groups that this switch can support is 26.
„...
Manual - Page 37
... to mechanisms in the network software that make the actual determination of which packets have priority. CoS refers to feature sets, or groups of services, that are assigned to users based on company policy. If a feature set includes priority transmission, then CoS winds up being implemented in QoS functions within the routers and switches in the...
Manual - Page 47
Firmware Update
The firmware update function supports web and command prompt window interface for the user to update the firmware to the switch. Both the method require the user to type in the password (login password) and type again for password confirmation, then click Update to start firmware update process.
Firmware Update interface
Please note that the system will erase the flash at first. ...
Manual - Page 48
Updating Firmware to the flash interface
After a while, the message shows as below to indicate the user that the update process is complete.
Update Complete message on web
As for TFTP firmware update, users can get into the command prompt window to proceed. The command prompt window can be opened by entering "cmd" (without quotes) into Start-Run or through...
Manual - Page 49
name of the firmware) and press enter to update.
Command Prompt Window
Note
The system will erase the flash at first and then update the new firmware during the update process. If the update process is not finished, the web page of Firmware Update will always be displayed when the switch powers on.
43