Gigabyte GA-6FASV2 driver and firmware
Related Gigabyte GA-6FASV2 Manual Pages
Download the free PDF manual for Gigabyte GA-6FASV2 and other Gigabyte manuals at ManualOwl.com
Manual - Page 2
...-6FASV1/GA-6FASV2 Motherboard Component 8 Chapter 2Hardware Installation Process 10 2.1.Installing Processor and CPU Heat Sink 10
2.1.1.Installing CPU ...10 2.1.2.Installing Cooling FAN 11
2.2.Installing memory modules 12 2.3.Connect ribbon cables, cabinet wires, and power supply 14
2.3.1. I/O Back Panel Introduction 14
2.4.Connectors and Jumper Setting Introduction 17 Chapter 3BIOS Setup...
Manual - Page 4
Item Checklist
The GA-6FASV1 motherboard The GA-6FASV2 motherboard Serial ATA cable x 2 I/O Shield Kit CD for motherboard driver & utility The GA-6FASV1/The GA-6FASV2 quick reference guide
GA-6FASV Series Motherboard
* The items listed above are for reference only, and are subject to change without notice.
4
Manual - Page 5
GA-6FASV Series Motherboard
Chapter 1 Introduction
1.1. Considerations Prior to Installation
Preparing Your Computer The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please follow the instructions below: 1. Please turn off the computer and unplug its power cord. 2. When ...
Manual - Page 6
GA-6FASV Series Motherboard
1.2. Features Summary
Form Factor CPU
Chipset Memory
I/O Control Expansion Slots
SATA RAID Controller On-Board VGA On-Board LAN Internal Connector
Rear Panel I/O
9.6" x 9.6" Micro ATX size form factor, 6 layers PCB Supports single Intel® LGA1156 (socket H1) processor Support Lynnfield (Quad-core)
processor Enhanced Intel ...
Manual - Page 7
... RJ45 LAN ports (GA-6FASV2) 1 x NMI switch Winbond W83627DHG-P controller Enhanced features with CPU Vcore, DDR3 1.5V, VCC3 (3.3V),
12V, 5V, and System Temperature Values viewing CPU/System Fan Revolution Detect CPU shutdown when overheat Phoenix BIOS on 16Mb flash RAM Supports S4, S5 under Windows Operating System AC Recovery...
Manual - Page 10
... the socket. 3. Apply thermal grease on the processor before placing cooling fan. 4. Please make sure the CPU type is supported by the motherboard. 5. If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause
improper installation. Please change the insert orientation.
2.1.1. Installing CPU
Step 1 Raise the metal locking lever on the socket. Remove...
Manual - Page 11
2.1.2. Installing Cooling FAN
GA-6FASV Series Motherboard
Step 1 Attach the cooling fan on the processor socket. Step 2 Turning and push vertically the push pin as arrow direction shown. Step 3 Connect processor fan cable connector to the processor fan connector.
11
Manual - Page 12
... sure that the computer
power is switched off to prevent hardware damage. 3. Memory modules have a foolproof insertion design. A memory module can be installed
in only one direction. If you are unable to insert the module, please switch the direction. The motherboard supports DDR3 memory modules, whereby BIOS will automatically detect memory capacity and specifications. Memory modules are designed...
Manual - Page 15
... LAN Ports The LAN port provides Internet connection of Gigabit Ethernet with data transfer speeds of 10/100/1000Mbps. USB Port Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure your OS supports USB controller. If your OS does not support USB controller...
Manual - Page 18
... sure that all components and devices are properly installed. Align the power connector with its proper location on the motherboard and connect tightly. The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power connector is not connected, the system will not start. Caution! Please use a power supply that is able to support the system voltage requirements...
Manual - Page 21
... ) SATA 0~5 (Serial ATA cable connectors) SATA 3Gb/s can provide up to 300MB/s transfer rate. Please refer to the BIOS setting for the SATA 3Gb/s and install the proper driver in order to work properly.
7
Pin No. Definition
1
GND
2
TXP
3
TXN
4
GND
5
RXN
1
6
RXP
7
GND
13 ) BAT (Battery) If you want to erase CMOS... 1.Turn OFF the computer and unplug the power cord...
Manual - Page 26
... the items in standard compatible BIOS.
Advanced This setup page includes all the items of Phoenix BIOS special enhanced features. (ex: Auto detect fan and temperature status, automatically configure hard disk parameters.)
Power This setup page includes all the items of Green function features.
Security Change, set, or disable password. It allows you to limit...
Manual - Page 42
... Disables on-board serial ATA function. SATA Mode Selection
IDE RAID ACHI
Determine IDE as the SATA mode. (Default setting) Enable the SATA RAID function.
Set this item to enable SATA AHCI function for WinXP-SP1+IAA driver supports AHCI mode.
SATA Port 0/1/2/3/4/5
The category identifies the types of Serial SATA hard disk from drive 0 to 5 that has been installed in the computer. System will...
Manual - Page 43
...types. Users: Set parameters by User. Auto: Set parameters automatically. (Default setting) CD-ROM: Use for ATAPI CD-ROM drives or double click [Auto] to set all HDD parameters automatically. ATAPI Removable: Removable disk drive is installed here.
Multi-Sector Transfer
This field displays the information of Multi-Sector Transfer Mode. Disabled: The data transfer from and to the device occurs one...
Manual - Page 51
... for boot sector.
Figure 4: Security
Set Supervisor Password You can install and change this options for the setup menus. Type the password up to 6 characters in length and press . The password typed now will clear any previously entered password from the CMOS memory. You will be asked to confirm the entered password. Type the password again and press . You may...
Manual - Page 54
System Management
GA-6FASV Series Motherboard
Figure 5-1: System Management
Server Management This category allows user to view the server management features. Including information of Motherboard Hardware information and software information.
54
Manual - Page 55
..., it will use a port on the motherboard to run console redirection function.
On-board COM A Use Serial Port A as the COM port address.
On-board COM B Use Serial Port B as the COM port address.
Disabled
Disable this function. (Default setting)
Flow Control This option provide user to enable the flow control function.
None
Not supported. (Default setting)
XON/OFF
Software control.
CTS/RTS...
Manual - Page 61
GA-6FASV Series Motherboard Load Setup Default
if you highlight this item and press Enter, a dialog box asks if you want to install optimal settings for all the items in the Setup utility. Press the Y key to indicate Yes, and then press Enter to install the optimal settings. Discard Changes Select this item and press Enter to discard any...