Intel RMS25CB080 driver and firmware
Related Intel RMS25CB080 Manual Pages
Download the free PDF manual for Intel RMS25CB080 and other Intel manuals at ManualOwl.com
Hardware User's Guide - Page 1
...: G26616-002
Warranty Notice: Adding a battery onto an Intel® RAID controller will limit the warranty of this product. Returns determined to be caused by battery installation damage, stripped screws, or other damage resulting from the battery installation will not be covered. ESD damage to the board will also not be covered by the warranty. The...
Hardware User's Guide - Page 5
... devices and cables: Hazardous electrical conditions may be present on power, telephone, and communication cables. Turn off the server and disconnect the power cord, telecommunications systems, networks, and modems attached to the server before opening it. Otherwise, personal injury or equipment damage can result.
Electrostatic discharge (ESD) and ESD protection: ESD can damage disk drives, boards...
Hardware User's Guide - Page 7
... importantes iii Warnings ...v
Chapter 1: About the Intel® RAID Smart Battery AXXRSBBU9 1
Chapter 2: Installing the Hardware 3
Remote Battery Connecting Cables 4 Important Pre-installation Considerations 4 Installing the Intel® RAID Smart Battery AXXRSBBU9 5
Removing the RAID Controller 5 Installing the Intel® RAID Smart Battery AXXRSBBU9 5 Connecting the Plastic Battery...
Hardware User's Guide - Page 13
...written to the storage device. This risk factor is eliminated when the Intel® RAID Controller has a BBU installed.
The Intel® RAID Smart Battery Backup Unit monitors the voltage level of the DRAM modules installed on the Intel® RAID Controller. If the voltage drops below a predefined level, the battery backup module switches the memory power source from the controller to the battery...
Hardware User's Guide - Page 15
... the location of this connector) is used to remotely connect to an Intel® RAID Controller using supplied cable. Only the top side of the battery pack is visible after it is installed on the RAID controller.
A. Board to board Connector B. Remote BBU Connector
Figure 1. Top and Bottom View of the Intel® RAID Smart Battery AXXRSBBU9
Intel® RAID Smart Battery AXXRSBBU9 User's Guide
3
Hardware User's Guide - Page 16
... Memory Board which is mounted on the RAID controller. Intel recommends mounting the battery remotely from the RAID controller when possible to provide additional cooling.
Table 1. Cable Compatability
Intel® RAID Controller or Server System Intel® RAID Controller RS25DB080.
27-inch Cable
X (Required to connect to cache memory board on the RAID controller)
Important Pre-installation...
Hardware User's Guide - Page 17
...data cables to make sure the two tiny catches release. 3. Carefully remove the RAID controller from the server board. For more information on removing add-in cards, refer to the server board documentation. 4. Place the RAID controller on a flat, clean, static-free surface.
Installing the Intel® RAID Smart Battery AXXRSBBU9
You can set up a remote connection to the RAID Controller.
Intel®...
Hardware User's Guide - Page 18
... RIGHTS RESERVED
Setting up a Remote Connection to the RAID Controller
To install the Intel® RAID Smart Battery AXXRSBBU9 on the RAID Controller through the J2 Remote BBU connector, do the following:. 1. Ground yourself, and remove the Intel® RAID Smart Battery AXXRSBBU9 from the
package. 2. Verify that the cache memory board is already installed on the supported RAID
controller.
! Li...
Hardware User's Guide - Page 19
...mechanism complies with the chassis requirements.
Intel® Server Chassis SC5400, Intel® Server Chassis SC5600, Intel® Server Chassis SC5650, Intel® Server Systems SR1600UR, SR1625UR, SR2600UR, and SR2625UR
1. Locate the installation clips inside the chassis. They are... tabs engage
with the clips in the chassis (Figure 4).
Intel® RAID Smart Battery AXXRSBBU9 User's Guide
7
Hardware User's Guide - Page 20
..., SR2600UR, SR2625UR, SR1550AL, and SR2500ALLX with Intel® Integrated RAID SROMBSASMP2, Intel® Server Systems SR1550AL, and SR2500ALLX
1. Locate the installation clips inside the chassis. They are located on the inside floor of the hassis, on the left side, near the front of the chassis by the power supply.
2. Align the tabs on the plastic...
Hardware User's Guide - Page 21
...appropriate set of instructions below for your server. 1. Route the cable through the cable holder on the edge of the chassis. 2. Connect the cable to the RAID controller or remote mounting board.
Installing the Intel® RAID Controller in the Server System
To install the Intel® RAID Controller back into the server system, do the following: 1. Align the RAID controller with the PCI Express...
Hardware User's Guide - Page 23
... Intel® RAID BIOS Console can be used to configure disk arrays and logical drives. It is independent of the operating system and can be accessed at server start up by pressing +.
To view the BBU information, do the following: 1. At boot, press + when prompted. 2. Once the Intel® RAID BIOS Console loads and the main menu appears, choose
Adapter...
Hardware User's Guide - Page 27
...After you install a new BBU, use one of the Intel configuration utilities to reset the battery recharge cycle counter to zero. For instructions, see "Monitoring the BBU with the Intel® RAID BIOS Configuration Utility...rechargeable batteries in public landfills. Be sure to recycle old battery packs properly. Intel would like to remind you that you must comply with all applicable battery disposal...