Intel SRCSATAWB - RAID Controller driver and firmware
Drivers and firmware downloads for this Intel item
Related Intel SRCSATAWB Manual Pages
Download the free PDF manual for Intel SRCSATAWB and other Intel manuals at ManualOwl.com
User Guide - Page 3
... Intel® RAID Controller SRCSATAWB, which can be used for SATA disk drives. It contains installation instructions and specifications. For details on how to configure the storage adapters, and for an overview of the software drivers, see the Software User's Guide on the Resource CD.
Audience
This document assumes that you have some familiarity with RAID controllers and related support devices...
User Guide - Page 5
... Characteristics 13
A. Drive Roaming and Drive Migration Install 15
Drive Roaming ...15 Drive Migration ...16
B. Installation / Assembly Safety Instructions 17
English ...19 Deutsch ...20 Français ...22 Español ...23 Italiano ...24
C. Regulatory and Certification Information 26
Electromagnetic Compatibility Notices 28
Intel® RAID Controller SRCSATAWB Hardware User's Guide
v
User Guide - Page 7
...support.intel.com/support/motherboards/server/. See also the tested hardware and operating system list for the RAID Controller SRCSATAWB to make sure the RAID card supports your operating system.
Usability
• The card ships with both a standard and a low-profile bracket. • Small, thin cabling with serial point-to-point 3.0 Gbps data transfer rates. • Support for non-disk devices...
User Guide - Page 8
... each read.
- Adaptive Read Ahead. Reads ahead and caches data only if doing sequential reads.
- I/O setting. Determines whether read operations check the cache before reading from disks.
✧ Cache I/O: Checks cache first, only reads disk if data is not in the cache. ✧ Direct I/O: Reads data directly from disk. (not cache)
3
Intel® RAID Controller SRCSATAWB Hardware User's Guide
User Guide - Page 11
... x4 or x8 PCI-Express* slot. • The Resource CD, which contains drivers and documentation. • SATA hard drives.
Note: Intel Corporation strongly recommends using an uninterruptible power supply (UPS).
Install the RAID Controller
1. Turn off the power to the system and all drives, enclosures, and system components. Remove the power cord(s).
2. Follow the instructions that came with...
User Guide - Page 12
... drives are supported.
Do not attempt to install a SAS drive. Only connect to a SATA drive or to a SAS/SATA backplane. The RAID Controller SRCSATAWB uses an advanced software stack that allows connections to SATA drives either directly or via SAS or SATA backplanes with or without expanders.
• Route the cables carefully. Check that controller and cables are all properly
attached.
7
Intel...
User Guide - Page 13
AF002211
Figure 3. Connecting Cables between the RAID Controller and Drives/Backplane
6. Install the server system cover and connect the power cords. See your server system documentation for instructions.
Intel® RAID Controller SRCSATAWB Hardware User's Guide
8
User Guide - Page 14
... display the RAID Controller SRCSATAWB number and firmware version. The numbering of the RAID controller follows the PCI slot scanning order used by the server board. 3. See the Intel® RAID Controller SRCSATAWB Quick Start User's Guide and the Software User's Guide for instructions to configure the RAID controller and to install the operating system drivers.
Replacing a Controller, Resolving...
User Guide - Page 15
...
J8
Internal SAS/SATA SFF8087 For ports 0 - 3
port connector
J9
Internal SAS/SATA SFF8087 For ports 4 - 7
port connector
J10
Firmware recovery 2-pin
jumper
jumper
This jumper needed only for flashes if the firmware is corrupted. The card does not function as a controller if this jumper is in place.
Figure 4. Card Layout s
Intel® RAID Controller SRCSATAWB Hardware User's Guide
10
User Guide - Page 16
Technical Specifications
Specification Processor Operating foltage Card size Array interface to host SATA bus speed Serial port SATA controller SATA ports Physical and virtual drive support Cache Firmware Compatible devices
Cabling
Redundant configuration Enclosure management Enclosure support Array support
Intel® RAID Controller SRCSATAWB LSI* 1078 Integrated RAID on Chip 500 MHz +3.3 V, +...
User Guide - Page 18
...condensing
Safety Characteristics
The Intel® RAID Controller SRCSATAWB meets or exceeds the requirements of UL flammability rating 94 V0. Each bare board is marked with the supplier name or trademark, type, and UL flammability rating. For the boards installed in a PCI bus slot, all voltages are lower than the SELV 42.4 V limit.
13
Intel® RAID Controller SRCSATAWB Hardware User's Guide
User Guide - Page 20
... to install and remove drives. 4. Determine the target requirements. 5. Make sure the drives are inserted properly. 6. Follow the instructions that came with your server system to remove the server cover. 7. Plug in and power on the system.
The controller detects the RAID configuration from the configuration data on the drives (COD).
15
Intel® RAID Controller SRCSATAWB Hardware User's Guide
User Guide - Page 21
...
8. Make sure all cables are properly attached and the RAID controller is properly installed.
9. Follow the instructions that came with your server system to remove the server cover.
10. Plug in and power on the system.
When you start the system, the controller detects the RAID configuration from the configuration data on the drives.
Intel® RAID Controller SRCSATAWB Hardware User's Guide
16
User Guide - Page 22
... a rug.
When working inside your computer:
• Do not attempt to service the computer system yourself, except as explained in this
guide and elsewhere in Intel documentation. Always follow installation and service instructions closely.
• Turn off your computer and any peripherals. • Disconnect your computer and peripherals from their power sources. Also
disconnect any telephone or...
User Guide - Page 23
...cable, make sure both connectors are correctly oriented and aligned.
• Handle components and cards with care. Don't touch the components or contacts on
a card. Hold a card ...from the antistatic packing material until you are ready to install the component in your computer. Just before unwrapping the antistatic packaging, be sure to...Intel® RAID Controller SRCSATAWB Hardware User's Guide
18
User Guide - Page 24
...-in cards, and other components are properly installed.
3. Attach the covers to the chassis with the screws removed earlier, and tighten them firmly.
4. Insert and lock the padlock to the system to prevent unauthorized access inside the system.
5. Connect all external cables and the AC power cord(s) to the system.
19
Intel® RAID Controller SRCSATAWB Hardware User's Guide
User Guide - Page 33
... television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
Intel® RAID Controller SRCSATAWB Hardware User's Guide...