Sony SDM-X53 - DELUXEPRO - 15" LCD Monitor driver and firmware
Drivers and firmware downloads for this Sony item
Related Sony SDM-X53 Manual Pages
Download the free PDF manual for Sony SDM-X53 and other Sony manuals at ManualOwl.com
Operating Instructions - Page 2
... you have any questions about this product, you may call; Sony Customer Information Services Center 1-800-222-7669 or http://www.sony.com/
Declaration of Conformity
Trade Name: Model: Responsible Party: Address:
Telephone Number:
SONY SDM-X53/X73/X93 Sony Electronics Inc. 16450 W. Bernardo Dr, San Diego, CA 92127 U.S.A. 858-942-2230
This device complies with part 15 of the FCC...
Operating Instructions - Page 3
... you have any questions about this product, you may call; Sony Customer Information Services Center 1-800-222-7669 or http://www.sony.com/
Declaration of Conformity
Trade Name: Model: Responsible Party: Address:
Telephone Number:
SONY SDM-X53/X73/X93 Sony Electronics Inc. 16450 W. Bernardo Dr, San Diego, CA 92127 U.S.A. 858-942-2230
This device complies with part 15 of the FCC...
Operating Instructions - Page 4
...;" and "" are not mentioned in each case in this manual.
Precautions 4 Identifying parts and controls 5
Setup 7
Setup 1: Connect the video signal cables 7 Setup 2: Connect the audio cord 8 Setup 3: Connect the power cord 8 Setup 4: Bundle the cords and cables 9 Setup 5: Turn on the monitor and computer 9 Setup 6: Adjust the height and tilt 10 Selecting the input signal (INPUT...
Operating Instructions - Page 5
...as a TV or various other household appliances. • In places subject to inordinate amounts of dust, dirt, or sand, for example near an open window or an outdoor exit. If setting up temporarily... materials.
Transportation
• Disconnect all cables from the monitor, and after fixing the LCD display at its highest point, grasp both side of the LCD display firmly taking care not to scratch the...
Operating Instructions - Page 8
...: • LCD display • Power cord • HD15-HD15 video signal cable (analog RGB) • DVI-D video signal cable (digital RGB) • Audio cord (stereo miniplug) • CD-ROM (utility software for Windows/Macintosh, Operating
Instructions, etc.) • Warranty card • Quick Setup Guide
Setup 1: Connect the video signal cables
• Turn off the monitor and computer before...
Operating Instructions - Page 10
... cover
Setup 5: Turn on the monitor and computer
1 Press the MAIN POWER switch located on the right side of the monitor in the direction of the [, if it is not already pressed. Make sure the 1 (power) indicator is lit in red.
Note The monitor is factory shipped with the MAIN POWER switch set to on ([).
MAIN POWER
lights in red
2
SDM...
Operating Instructions - Page 11
... video signal cable is properly connected. - Check that the input signal setting is correct by pressing the INPUT button (page 11).
• If "OUT OF RANGE" appears on the screen, reconnect the old monitor. Then adjust the computer's graphics board within the following ranges.
SDM-X53
Horizontal frequency Vertical frequency Resolution
Analog RGB 28-61 kHz
Digital RGB 28...
Operating Instructions - Page 15
... when the computer is connected to the monitor's HD15 input connector (analog RGB).
1 Set the resolution to 1024 × 768 (SDM-X53), 1280 × 1024 (SDM-X73/X93) on the computer.
2 Load the CD-ROM.
3 Start the CD-ROM, select the area and model, and display the test pattern. For Windows Click [Utility] t [Windows]/[Win Utility.exe]. For Macintosh Click [Utility] t [Mac]/[Mac Utility].
4 Press...
Operating Instructions - Page 16
...'s position manually (H CENTER /V CENTER)
If the picture is not in the center of the screen, adjust the picture's centering as follows.
1 Set the resolution to 1024 × 768 (SDM-X53), 1280 × 1024 (SDM-X73/X93) on the computer.
2 Load the CD-ROM.
3 Start the CD-ROM, select the area and model, and display the test pattern. For Windows Click [Utility] t [Windows]/[Win...
Operating Instructions - Page 22
... Resolution: 1024 × 768 or less (SDM-X53), 1280 × 1024 or less (SDM-X73/X93)
If using Windows,
• If you replaced an old monitor with this monitor, reconnect the old monitor and do the following. Select "SONY" from the "Manufacturers" list and select "SDM-X53, SDMX73 or SDM-X93" from the "Models" list in the Windows device selection screen. If "SDM-X53, SDM-X73 or SDM...