Toshiba PA3314U driver and firmware
Related Toshiba PA3314U Manual Pages
Download the free PDF manual for Toshiba PA3314U and other Toshiba manuals at ManualOwl.com
Advanced Port Replicator III (PA3314U-1PRP) Users Guide - Page 2
... manual's production. However, succeeding computers and manuals are subject to change without notice. TOSHIBA assumes no liability for damages incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manual.
Trademarks
PS/2 is a trademark of International Business Machines Corporation. Windows is a registered trademark of Microsoft Corporation. Ethernet...
Advanced Port Replicator III (PA3314U-1PRP) Users Guide - Page 3
... TV reception. Shielded cables must be used between the external devices and the computer's parallel port, external monitor port, DVI port, PS/2 mouse port, PS/2 keyboard port, serial port, i.LINK port and USB ports. Changes or modifications made to this equipment, not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user's authority to operate the equipment.
The LAN...
Advanced Port Replicator III (PA3314U-1PRP) Users Guide - Page 16
... Bus (USB 2.0) ports
Four Universal Serial Bus ports are on the back. The ports comply with the USB 2.0 standard The ports also support USB 1.1. The number of the USB ports of DMI information may differ from the number of actual USB ports. For DMI information, a USB port may be displayed as two ports.
i.LINK(IEEE1394) Connect an external device, such as a digital video camera port to this port...
Advanced Port Replicator III (PA3314U-1PRP) Users Guide - Page 22
CONNECTIONS
User's Manual
Disconnecting the Port Replicator
To disconnect the Port Replicator, follow the steps below. 1. Set the computer lock to the unlock position. 2. Make sure you perform one of the following: • Save all your work. • Turn off the computer's power in any mode: boot, suspend or hibernation. • Perform any software disconnect operation required by the...
Advanced Port Replicator III (PA3314U-1PRP) Users Guide - Page 30
User's Manual
Connecting
1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer.
Figure 4-4 Connecting the i.LINK cable 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ❑ You may need to install drivers for your i.LINK devices. ❑ Not all i.LINK devices have been tested, therefore...
Advanced Port Replicator III (PA3314U-1PRP) Users Guide - Page 33
...
Keyboard problems can be caused by your setup configuration. For more information refer to your computer user's manual.
Problem
No response from keyboard
Output to screen is garbled
Procedure
Make sure the keyboard cable is firmly connected to the PS/2 keyboard port on the Port Replicator.
Make sure the software you are using is not remapping the...
Advanced Port Replicator III (PA3314U-1PRP) Users Guide - Page 34
....
Problem
Procedure
On-screen pointer
Check for a firm connection between the
does not respond to Port Replicator's serial port and the
serial mouse operation cable's 9-pin connector.
Did you connect the mouse before turning on the computer?
Is your software configured to recognize the mouse? Check the software documentation.
If problems persist, contact your dealer.
5-4
TROUBLESHOOTING
Advanced Port Replicator III (PA3314U-1PRP) Users Guide - Page 35
... supplying power.
Computer/printer
Make sure the printer is turned on and is
do not communicate online (ready to use).
Inspect the cable connecting the printer to the Port Replicator for damage. Make sure it is securely connected.
A parallel printer connects to the parallel port and a serial printer to the serial port. Make sure the ports are configured correctly.
Make sure your software is...
Advanced Port Replicator III (PA3314U-1PRP) Users Guide - Page 37
...
Refer also to your computer user's manual
Problem No sound is heard
Procedure Adjust the volume control dial.
Check the software volume settings.
Make sure the line-out connection is secure.
Check Windows Device Manager. Make sure the sound function is enabled and that settings for I/O address, Interrupt level and DMA are correct for your software and do not conflict...
Advanced Port Replicator III (PA3314U-1PRP) Users Guide - Page 38
... hub, will not work until the OS has started.
If problems persist, contact your dealer.
Modem
Refer also to your computer user's manual.
Problem
Procedure
Communication software can't initialize modem
Make sure the computer's internal modem settings are correct. Refer to Modem Properties in the Control Panel.
You can hear a dial tone but can't make a call
If the call is...
Advanced Port Replicator III (PA3314U-1PRP) Users Guide - Page 40
User's Manual
LAN
Problem Cannot access LAN
Procedure
Contact the system administrator or if the problem persists, contact your dealer.
i.LINK (IEEE1394)
Problem
i.LINK device does not function
Procedure
Make sure the cable is securely connected to the computer and to the device.
Make sure the device's power is turned on.
Reinstall the drivers. Open the Windows Control Panel and double-click...
Advanced Port Replicator III (PA3314U-1PRP) Users Guide - Page 41
... you contact TOSHIBA, please investigate your problem using the following resources: ‰ Review troubleshooting sections in the documentation for your computer,
software and peripheral devices. ‰ If a problem occurs when you are running software applications, consult the
software documentation for troubleshooting suggestions. Call the software company's technical support for assistance...