Lexmark WinWriter 150c driver and firmware
Drivers and firmware downloads for this Lexmark item
Related Lexmark WinWriter 150c Manual Pages
Download the free PDF manual for Lexmark WinWriter 150c and other Lexmark manuals at ManualOwl.com
Service Manual - Page 2
...technical inaccuracies or typographical errors. Changes are periodically...WinWriter is a trademark of Lexmark International, Inc. © Copyright Lexmark International, Inc. 1995, 1997. All Rights Reserved. UNITED STATES GOVERNMENT RESTRICTED RIGHTS This software and documentation are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to restrictions as set...
Service Manual - Page 6
... and safety instructions.
2. Diagnostic Information contains error code table, symptom table, and service checks used to isolate failing field replaceable units (FRUs).
3. Diagnostic Aids contains tests and checks used to locate or repeat symptoms of printer problems.
4. Repair Information provides instructions for making printer adjustments and removing and installing FRUs.
5. Connector...
Service Manual - Page 10
... this manual leads you to the correct field replaceable unit (FRU) or part. Use the error code charts, symptom index, service checks, and diagnostic aids to determine the symptom and repair the failure. Begin with "Start" on page 3.
This printer can be serviced without being connected to a host computer. The user is directed, in the WinWriter 150c Printer Control program...
Service Manual - Page 20
...8226; An open or short in the motor driver on the
system board • A bind in the paper feed mechanism
With the paper feed motor cable disconnected from the system board, check for 100 ohms (±20 ohms)... turns in one direction only, replace the system board. Binds in the paper feed motor or gear train can cause intermittent false paper jam errors. Remove the paper feed motor and check the ...
Service Manual - Page 22
... begin this service check:
• Check the entire paper path for obstructions. • Be sure the paper guides are not worn or broken and are
positioned against the paper without binding or buckling the paper.
• Be sure the correct type of paper is being used. • Be sure the printer is installed on...
Service Manual - Page 28
... a complete test page of black and color patterns, be sure the print cartridges are in good condition. Install a black print cartridge in the left side of the printhead cradle and a color print cartridge in the... allowing one second between each press. Pages continue to print until you turn off the power or unplug the printer. The first line of this test page is the code level and code level date....
Service Manual - Page 29
... performs a wrap around test between the printer parallel port and the parallel port test connector. This test requires a parallel port wrap plug. Install the wrap plug in the parallel port before you start the test. If the test is successful, the power on light flashes. If the test is not successful, the power on light remains off. To run...
Service Manual - Page 34
... to make adjustments to the printer and how to remove defective ...ESD-sensitive parts, follow the instructions below in addition to all the usual precautions, such as turning off power before removing logic boards:
• Keep the ESD...• Prevent ESD-sensitive parts from being accidentally touched by
other personnel. Install machine covers when you are not working on the machine, and do not ...
Service Manual - Page 43
... from the mid frame by pulling it out of
the four mounting clips. Spread the right side frame and remove the large feed roll.
Note: Install the compound idler gear after the machine is installed in the base assembly.
Repair Information 34
Service Manual - Page 45
...Remove the front cover. 2. Remove the rear cover. 3. Remove the carrier frame assembly. 4. Remove the paper load door and manual insert tray. 5. Using a small screwdriver, break the four prongs off the
compound idler gear [A] and remove the.... Note the relationship of the parts. Note: Install a new compound idler gear [A] after the machine is installed in the base assembly.
B
A
Repair Information 36
Service Manual - Page 55
... paper feed motor cable. Note: The head to head and bidirectional printing alignments will be reset to factory defaults. The user, through the WinWriter 150c Printer Control program, is directed to perform these alignments. When reinstalling the system board, it is easier to insert the printhead cables in the four connectors prior to installing the board.
Repair Information 46