Samsung ML-4551N - B/W Laser Printer driver and firmware
Drivers and firmware downloads for this Samsung item
Related Samsung ML-4551N Manual Pages
Download the free PDF manual for Samsung ML-4551N and other Samsung manuals at ManualOwl.com
User Manual (ENGLISH) - Page 24
...to monitor the printer's status and alerts you when an error occurs during printing.
network utilities CD
(ML-4551N, ML-4551ND only)
Windows
• SyncThru™ Web Admin Service: Use this web-based program to remotely manage, monitor, and troubleshoot network printers.
• Set IP: Use this program to set your printer's TCP/IP addresses.
• Network Printer User's Guide in PDF
3.1
User Manual (ENGLISH) - Page 25
...
X
X
X
Note • Overlay is not supported in Windows NT 4.0.
System requirements
Before you begin, ensure that your system meets the following requirements:
Windows
Item Operating system CPU
RAM
Free disk space
Internet Explorer
Requirements
Recommended
Windows 98/Me/NT 4.0/2000/XP/2003
Windows 98/
Pentium II
Me/NT 4.0/2000 400 MHz or
higher
Windows XP/ 2003
Pentium III 933 MHz...
User Manual (ENGLISH) - Page 55
... resolution to 1200 dpi (Best), change it to 600 dpi (Normal). See the Software Section.
Change the port setting to the USB or network port to improve print speed.
Your printer prints A4-sized paper at 43 ppm and lettersized paper at 45 ppm. If you use the ML-4551ND and install an option duplex unit in the ML4550 or ML-4551N...
User Manual (ENGLISH) - Page 56
...using Windows 98/Me, the Spooling Setting may be set incorrectly.
From the Start menu, choose Settings and Printers. Rightclick the Samsung ML-4550 Series PCL 6 printer icon, choose Properties, click the Details tab, and then choose the Spool Settings button. Select the desired spool setting.
The computer may have insufficient random-access memory (RAM).
Install more memory in your printer. See...
User Manual (ENGLISH) - Page 59
... page and verify that the PostScript version is available for printing.
• Install the PostScript driver; to installing the PS printer driver, see the Software Section.
• If problem consists, contact a service representative.
"Limit Check Error" message appears.
The print job was too complex.
You might need to reduce the complexity of the page or install more memory.
9.13
User Manual (ENGLISH) - Page 60
...; Check if the printer driver is installed in your system. Open Unified Driver Configurator and switch to the Printers tab in Printers configuration window to look at the list of available printers. Make sure that your machine is displayed on the list. If not, please, invoke Add new printer wizard to set up your device.
• Check if the printer is started. Open...
User Manual (ENGLISH) - Page 62
... your computer. To install the PostScript printer driver, see the Software Section.
2 Click the Windows Start menu.
3 For Windows 98/Me/NT 4.0/2000, select Settings and then Printers. For Windows XP/2003, select Printers and Faxes.
4 Select the Samsung ML-4550 Series PS printer.
5 Click the right mouse button on the printer icon and select Properties.
6 For Windows 98/Me, select the Device Option...
User Manual (ENGLISH) - Page 69
... fonts, OCR fonts
• IEEE 1284 Bidirectional Parallel Standard - Modes supported: Compatible, Nibble, Byte, ECP
• USB Interface Standard - USB 2.0 compliant
- 480 Mbps 1 port
• Network Interface - ML-4551N, ML-4551ND: enthernet 10/100 Base TX wired LAN
OS compatibility Printer driverse
• Windows 98/Me/NT 4.0/2000/XP/2003 • Various Linux OS • Mac 8.6 ~ 9.2/10...
User Manual (ENGLISH) - Page 73
... SECTION
CONTENTS
Chapter 1: INSTALLING PRINTER SOFTWARE IN WINDOWS
Installing Printer Software ...4 Installing Software for Local Printing 4 Installing Software for Network Printing 7
Changing the Software Language 10 Reinstalling Printer Software 10 Removing Printer Software ...11
Chapter 2: BASIC PRINTING
Printing a Document ...12 Printer Settings ...13
Layout Tab ...13 Paper Tab ...14...
User Manual (ENGLISH) - Page 76
...
A local printer is a printer directly attached to your computer using the printer cable supplied with your printer, such as a USB or parallel cable. If your printer is attached to a network, skip this step and go to "Installing Software for Network Printing" on page 7. You can install the printer software using the typical or custom method.
NOTE: If the "New Hardware Wizard" window appears during...
User Manual (ENGLISH) - Page 77
... sure that the printer is connected to your computer
and powered on.
2 Insert the supplied CD-ROM into your CD-ROM drive.
The CD-ROM should automatically run, and an installation window appears. If the installation window does not appear, click Start and then Run. Type X:\Setup.exe, replacing "X" with the letter which represents your drive and click OK.
5 Installing Printer Software in Windows
User Manual (ENGLISH) - Page 78
... printed at the end of the installation. • The installation window that appears in this User's Guide may differ depending on the printer and interface in use.
6 Select the components to be installed and click Next.
NOTE: You can change the desired installation folder by clicking [Browse].
7 After the installation is finished, a window asking you to
print a test page...
User Manual (ENGLISH) - Page 79
... sent to the Samsung web site.
Otherwise, just click Finish.
If the installation window does not appear, click Start and then Run. Type X:\Setup.exe, replacing "X" with the letter which represents your drive and click OK.
Installing Software for Network Printing
When you connect your printer to a network, you must first configure the TCP/IP settings for the printer. After you have...
User Manual (ENGLISH) - Page 80
... choose individual components to install and set a specific IP address.
1 Make sure that the printer is connected to your network
and powered on. For details about connecting to the network, see the supplied printer's User's Guide.
2 Insert the supplied CD-ROM into your CD-ROM drive.
The CD-ROM should automatically run, and an installation window appears. If the installation window does not appear...
User Manual (ENGLISH) - Page 81
... a Network Configuration page.
b. Configure an IP address, subnet mask, and gateway for the printer manually and click Configure to set the specific IP address for the network printer.
c. Click Next.
NOTE: After setup is complete, if your printer driver doesn't work properly, reinstall the printer driver. See "Reinstalling Printer Software" on page 10.
9 Installing Printer Software in Windows
User Manual (ENGLISH) - Page 82
... network. To add the printer to the network, enter the port name and the IP address for the printer.
• To find a shared network printer (UNC Path), select Shared Printer [UNC] and enter the shared name manually or find a shared printer by clicking the Browse button.
You will see a component list so that you can reinstall any item individually.
10 Installing Printer Software in Windows
User Manual (ENGLISH) - Page 83
... a component list so that you can remove any item individually.
4 Select the components you want to remove and then click
Next.
5 When your computer asks you to confirm your selection,
click Yes. The selected driver and all of its components are removed from your computer.
6 After the software is removed, click Finish.
11 Installing Printer Software in Windows
User Manual (ENGLISH) - Page 87
... to image the text in your document. Select the appropriate setting according to the status of your document. This option may be available only in Windows 9x/Me, depending on your particular printer model. - Download as Outline: When this option is selected, the
driver will download any TrueType fonts that are used in your document not...
User Manual (ENGLISH) - Page 96
... having to open the file. It sends data through the Windows spooler using the port of the printer driver. It only supports PDF format. To installing this program, you should select Custom and put a check mark in this program when you install the printer driver.
Printing
There are several ways you can print using Direct Print Utility.
From the...
User Manual (ENGLISH) - Page 99
... Smart Panel Program Settings
Right-click (in Windows or Linux) or click (in Mac OS X) the Smart Panel icon and select Options. The following window opens.
• Display when job is finished for network printer: The computer shows the Smart Panel popup window or balloon when your job is complete in Windows. (Only for Windows network-supported printers.)
• Display when error occurs during...