Dell 7609WU - WUXGA DLP Projector driver and firmware
Drivers and firmware downloads for this Dell item
Related Dell 7609WU Manual Pages
Download the free PDF manual for Dell 7609WU and other Dell manuals at ManualOwl.com
RS232 Command Set Document - Page 2
... and Value, "02 (Low Byte), 00 (High Byte)" Command Code [COMMAND] ==> "Power On" Command, "01"
Projector Response Message Table Byte0 value: 0x00: Success 0x01: Invalid Command (on the control command list but no valid) 0x02: Error Command (includes CRC error and unknown commands)
Projector Response System Status Byte0, Byte1, Byte2 Byte0: 0x00 (Success) Byte1: 0xff (the...
RS232 Command Set Document - Page 3
...Aspect Ratio
0xefbe
Power OFF
0xefbe
Source-VGA Analog 1 ...Firmware Version
0xefbe 0xefbe 0xefbe 0xefbe 0xefbe 0xefbe 0xefbe
Auto Keystone Read 0xefbe
Aspect Ratio Read 0xefbe
Projector Mode Write
0xefbe
Projector Mode Read 0xefbe
Brightness Write Brightness Read
0xefbe 0xefbe
Address...VGA-A 0x02: VGA-B 0x03: S-Video 0x04: CVBS 0x05: Component 0x06: DisplayPort 0x07: HDMI-A 0x08: HDMI...
User's Guide - Page 2
... better use of your projector.
NOTICE: A NOTICE ...Dell Inc. is strictly forbidden. Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; DLP, DLP® logo and DarkChip™3 are either trademarks for Texas Instruments; Microsoft and Windows...Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
Model 7609WU
April 2008 Rev. A00
User's Guide - Page 3
... . 14 Connecting a DVD Player Using a Composite Cable 15 Connecting a DVD Player Using a Component (VGA to YPbPr) Cable 16 Connecting a DVD Player Using a Component (YPbPr to YPbPr) Cable 17 Connecting a DVD Player Using an HDMI Cable . . 18
Professional Installation Options 19 Installation for Driving Automatic Screen . . . . . 19 Connecting a Commercial RS232 Control Box . . . 20
Contents...
User's Guide - Page 10
Connecting a Computer Using a RS232 Cable
1 Power cable 2 RS232 cable
NOTE: The RS232 cable is not provided by Dell.Consult a professional installer for the cable and RS232 remote control software.
Connecting Your Projector 10
User's Guide - Page 19
Professional Installation Options
Installation for Driving Automatic Screen
1 Power cable 2 12V DC power cable 3 Automatic screen
NOTE: The 12V DC power cable is not provided by Dell.
The 12V DC power cable has to be connected to the DC 12V jack.
NOTE: Use a 12V DC plug
with a dimension 1.7mm (ID) x 4.00mm (DD) x
9.5 mm (shaft) to connect the automatic screen with the projector.
Connecting ...
User's Guide - Page 20
Connecting a Commercial RS232 Control Box
1 Power cable 2 RS232 cable 3 Commercial RS232 control box
NOTE: The RS232 cable is not provided by Dell. Consult a professional installer for the cable and RS232 remote control software.
Connecting Your Projector 20
User's Guide - Page 26
... use this button to adjust the image distortion caused by tilting the projector.
Allows you to adjust the OSD setting. You can also synchronize the projector to the input source. Auto Adjust does not operate if the onscreen display (OSD) is displayed.
Point the remote control towards the IR receiver and press a button.
Allows you to select...
User's Guide - Page 38
... Lamp menu, you can adjust the display settings of your projector. The Lamp menu provides the following options:
LAMP HOUR-Displays the operating hours since the last lamp timer reset. POWER SAVING-Select Yes to set the Power Saving delay period. The delay period is the time that you want the projector to wait without an input signal...
User's Guide - Page 44
... port is enabled.
If you are using a Dell™ portable computer,
press
(Fn+F8). For other
computers, see your respective
documentation.
• Ensure that all the cables are securely connected. See "Connecting Your Projector" on page 8.
• Ensure that the pins of the connectors are not bent or broken.
• Ensure that the lamp is securely installed...
User's Guide - Page 45
..., scrolling, or incorrectly displayed image
1 Press the Auto Adjust button on the remote control or the control panel.
2 If you are using a Dell™ portable computer, set the resolution of the computer to WXGA (1280 x 800) or XGA (1024 x 768):
a Right-click the unused portion of your Windows desktop, click Properties and then select Settings tab.
b Verify that the setting is 1280 x 800...
User's Guide - Page 46
... automatically shut down.
Unplug the power cable after 3minutes and then turn the display on again. If this problem persists, contact Dell™. (See "Contacting Dell™" on page 56)
TEMP light is solid amber
The projector is overheated and the display automatically shuts down. Turn the display on again after the projector cools down. If the problem persists...
User's Guide - Page 60
... with an HDMI
Cable 18 Connecting with an S-video
Cable 14
Ethernet (RJ45) cable 11, 12
HDMI cable 18 Installing a Driving Automatic
Screen 19 Optional installation 19
Power cable 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20
RS232 cable 10, 20
S-video cable 14 To Computer 9 To DVD Player 14 USB to USB cable 9
VGA to VGA cable 9, 13
VGA to YPbPr cable 16 YPbPr to YPbPr cable 17
Connection Ports 12...