Dell 1609WX - WXGA DLP Projector driver and firmware
Related Dell 1609WX Manual Pages
Download the free PDF manual for Dell 1609WX and other Dell manuals at ManualOwl.com
User Guide - Page 2
... better use of your projector.
NOTICE: A NOTICE ...Dell Inc. is strictly forbidden. Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; DLP, DLP® logo and DarkChip™2 are either trademarks for Texas Instruments; Microsoft and Windows...Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
Model 1609WX
May 2008 Rev. A01
User Guide - Page 22
... he image distortion caused by tilting the projector.
5 Right / Auto Adjust Allows you to adjust the OSD setting.
You can also use the Right button to synchronize the projector to the input source.
Auto adjust does not operate if the OSD is displayed.
6 IR Receiver
Point the remote control towards the IR receiver and press a button...
User Guide - Page 32
... Lamp menu, you can adjust the display settings of your projectors. The Picture menu, provides the following options:
LAMP HOUR-Displays the operating hours since the last lamp timer reset. POWER SAVING-Select Yes to set the Power Saving delay period. The delay period is the time you want the projector to wait without an input signal. By...
User Guide - Page 37
... port is enabled. If you are using a Dell™ portable computer, press (Fn+F8). For other computers, see your respective documentation.
• Ensure that all the cables are securely connected. See Connecting Your Projector on page 7.
• Ensure that the pins of the connectors are not bent or broken.
• Ensure that the lamp is securely installed...
User Guide - Page 38
... Adjust button on the remote control or the control panel.
2 If you are using a Dell™ portable computer, set the resolution of the computer to WXGA (1280x800) or XGA (1024 x 768):
a Right-click the unused portion of your Windows desktop, click Properties and then select Settings tab.
b Verify the setting is 1280x800 or 1024 x 768 pixels for the external monitor port.
c Press
(Fn+F8...
User Guide - Page 39
....
Unplug the Power cable after 3minutes then turn the display on again. If this problem persists, contact Dell™ (see Contacting Dell on page 47).
TEMP light is solid amber
The projector has overheated. The display automatically shuts down. Turn the display on again after the projector cools down. If the problem persists, contact Dell™ (see Contacting Dell on page...
Protocol Document - Page 2
... and Value, "02 (Low Byte), 00 (High Byte)" Command Code [COMMAND] ==> "Power On" Command, "01"
Projector Response Message Table Byte0 value: 0x00: Success 0x01: Invalid Command (on the control command list but no valid) 0x02: Error Command (includes CRC error and unknown commands)
Projector Response System Status Byte0, Byte1, Byte2 Byte0: 0x00 (Success) Byte1: 0xff (the...
Protocol Document - Page 3
...Power Off Source-VGA Analog 1 Source-S-Video Source-Composite Key Pad Lock On Key Pad Lock Off Current Source
Header (WORD)
0xefbe 0xefbe 0xefbe 0xefbe 0xefbe 0xefbe 0xefbe 0xefbe 0xefbe 0xefbe 0xefbe 0xefbe 0xefbe 0xefbe 0xefbe 0xefbe 0xefbe 0xefbe
Address...Hour Firmware Version Auto...Projector Mode Write
0xefbe
0x10
0x0006
0x9ae3
0x1111
Projector...None 0x01: VGA-A 0x02: VGA-B 0x03: DVI-D 0x04:...