Sony CDP-C515 driver and firmware
Related Sony CDP-C515 Manual Pages
Download the free PDF manual for Sony CDP-C515 and other Sony manuals at ManualOwl.com
Operating Instructions - Page 2
... (servicing) instructions in the literature accompanying the appliance.
Information
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device...
Operating Instructions - Page 3
Table of Contents
Introduction
Introduction
3
Precautions
4
Installation
4
Connections
5
Location of controls
6
Front panel
6
Remote commander
7
Installing batteries in the remote commander
7
Playing a disc - Continuous play
Information display
9
Selecting a desired disc
10
Locating a particular selection
10
Locating a particular point in a selection
10
Playing in a ...
Operating Instructions - Page 4
... servicing to qualified personnel only.
On operation When the unit is not used, turn the power off, to conserve energy and to extend the useful life of your unit
For detailed safety precautions, see the leaflet "IMPORTANT SAFEGUARDS".
If you have any questions or problems concerning your unit, please contact you nearest Sony dealer...
Operating Instructions - Page 6
... pages indicated in • for details.
1 POWER switch 0
2 DISC 1-5 buttons 0
3 REPEAT button 0
4 Display window 5 CHECK (program check) button 0 6 CLEAR (program clear) button
0 7 FADER button
8 EDIT/TIME FADE button
9 1441/044 (AMS*) buttons 0 10 Pi- (play) button 0 11 II (pause) button 0
12 • (stop) button 0
13 4444/101. (manual search) buttons 0
14 OPEN/CLOSE button...
Operating Instructions - Page 7
... a year of normal operation can be expected
when using the Sony SUM-3(NS) batteries. • When the batteries are run down, the remote
commander will not operate the unit. In this case, replace both batteries with new ones.
Notes on the remote commander and remote control operation • Keep the commander away from extremely hot...
Operating Instructions - Page 9
...display
nchanges to give you the following information. Elapsed time in a selection (automatically displayed when play begins)
Remaining time in the selection "- -" indication will appear in the display window... mode. It
will not be displayed by pressing the TIME button during program or shuffle mode. • Total remaining time will be displayed, if time fade is set during program or shuffle.
9
Operating Instructions - Page 12
...-
0
e
_ 0
2,4,5,7
1
' s
2
>10 -4r,5
DISC SKIP
.,6, 0cFLIEoWsE
PROGRAM
"PROGRAM" is displayed.
3 Choose the Disc.
osc _
1
2
3
If you program a whole disc, go on to step 5....
0.343) 4
so fic
/80010 5 :S. :3 L•t)
The selection is stored, and the flashing numbers in the window lights up.
5 To program additional selections from the same disc, repeat step 4. To program additional ...
Operating Instructions - Page 13
... side B When the selections for side A have been played, the unit
will pause. ("B" lights up.) Set the tape to the beginning of side B, then press► or
lit
The selections for side B will ... play.
• Power is turned off.
To check the step of programmed selections Press TIME during stop mode. The number of programmed selections will be displayed for few seconds in the window.
To check the ...
Operating Instructions - Page 15
... selection(s) to fit the remaining time. To disappear "EDIT" in the window, press • button.
To play the program Press IN.% The selections...the unit will pause. "B" lights up in the tape side indicator. Set the tape to the beginning of side B, then press IP. or ... your own program of the desired selections.
See page 12 for instructions. 2 Follow the procedure as shown on the preceding page.
Just...
Operating Instructions - Page 17
.../Fade out cannot be operated when the DIGITAL (optical) OUT is used for connections.
Fading in...start fading out. 1;="°11flashes in the window, and play fades out and unit enters the...player fades out.
To cancel time fade lime fade will be canceled when - EDIT/TIME FADE is pressed once again. - 4141/0010. (manual search) is pressed during play.
To display the time remaining until the time set...
Operating Instructions - Page 18
...scan a disc from beginning to end and determine the loudest portion (peak level) of the disc, then play that portion repeatedly. This function will make it easier for you to adjust to the optimum level when
recording... on tape. You can use this function in the continuous, shuffle and
program play modes.
To set peak search
Press PEAK SEARCH during stop. "PEAK" blinks in the window. The...