HP Indigo W7200 driver and firmware
Drivers and firmware downloads for this Hewlett-Packard item
Related HP Indigo W7200 Manual Pages
Download the free PDF manual for HP Indigo W7200 and other HP manuals at ManualOwl.com
Writing Head Service Instructions -- CA393-00150Document P/N: Rev 06Revision number: - Page 4
... guide include the use of a Print Care wizard. The following software must be installed on the press computer in order to use the Print Care wizards:
For the HP Indigo 7000 Digital Press ● HP Indigo press software version 8.2 or higher ● HP Indigo Print Care version 1.3 or higher
For the HP Indigo WS6000 Digital Press ● HP Indigo press software version 8.1.1 or higher ● HP...
Writing Head Service Instructions -- CA393-00150Document P/N: Rev 06Revision number: - Page 5
... the installation and configuration of the writing head.
Visual inspection
Follow the steps below to check the exit window and interface rubber washers. 1. Check that the exit window is clean...cables
Follow the steps below for mounting the writing head and connecting the cables 1. Switch the press and computer off. 2. Verify that the serial number on the parameter diskette or CD matches the serial...
Writing Head Service Instructions -- CA393-00150Document P/N: Rev 06Revision number: - Page 10
...- for new writing head installation on HP Indigo w7200 Digital Press only
Refer below for new writing head installation on HP Indigo w7200 Digital Press only. 1. Disconnect the MCN1, MCN2, WHEL1 and WHEL2 USB cables. 2. Run CP210xSetIDs.exe from c:\unicorn\release. The CP210x Set IDs window opens. 3. Connect the newly installed WHEL1 or WHEL2 USB cable and click Update Device List. 4. Depending on...
Writing Head Service Instructions -- CA393-00150Document P/N: Rev 06Revision number: - Page 11
... CP210x Set IDs window
Initial image placement
Follow the steps for image placement. NOTE: Skip this step during an initial press installation. 1. Click Main Menu > Problem Handling > HP Indigo Print Care > Component Service > Writing Head >
Installation of Writing Head with Manual Interface. 2. Click Go to Process > Run Image Placement Wizard. 3. Click Run Wizard. Follow the wizard instructions...
Writing Head Service Instructions -- CA393-00150Document P/N: Rev 06Revision number: - Page 17
..., copy the Saved value to the Dynamic value.
Initial image placement (only for the 7000 Press)
If HP Indigo Print Care is not available perform the following procedure: 1. Click Main Menu > Problem Handling > CE Wizards. 2. Select Image Placement Calibration. 3. Click Run Process. Follow the wizard instructions.
Skew adjustment (only for the 7000 and W7200 Presses...
Writing Head Service Instructions -- CA393-00150Document P/N: Rev 06Revision number: - Page 26
....
If the HT_VER1 value is "not installed" or "other", then select HT_VER1. Click Save and restart the terminals (Ctrl + X in the MCN window and WHEL terminal window). 2. Copy the SOSCViewer.exe file to the C\Unicorn\Engine folder. 3. Double-click the SOSCViewer.exe file. 4. Select Start download, and wait until the camera screen appears. 5. Center the spots...
Dripping Prevention and ITM Heating Hood Service -- CA393-10100 Rev 00 - Page 2
... hood...14 Removing and installing the catch tray fan assembly...16 Removing and installing the IHH controller unit (for presses with external IHH controller 17 Wiring the dripping ... rate...33 IHH controller unit troubleshooting ...34 Baselining the dripping prevention kit ...36
Appendix A More theory ...63 Software settings ...63 Theory for presses without external IHH controller...63
Appendix B ...
Dripping Prevention and ITM Heating Hood Service -- CA393-10100 Rev 00 - Page 10
... before you begin the procedures. 1. Check the following SysTab parameter:
engineConfigTopic > ihhInstalled is set to HT_VER1, and bypassTableTopic > Ihh is set to FALSE, and engineConfigTopic > feedSuctionNautilairInstalled is set to TRUE. 2. Shut down the press software. 3. Shut down the power to the press.
Removing and installing the new ITM suction blower
Follow these steps to remove and...
Dripping Prevention and ITM Heating Hood Service -- CA393-10100 Rev 00 - Page 40
...Guide):
● Required ambient temperature 20 to 25° C (68 to 77° F) ● Required ambient relative humidity 50 to 70 percent non-condensing ● Required fresh air flow +150 cfm 2. Check chiller set...
Follow these steps to shutdown the press. 1. Shutdown the press software and computer. 2. Turn off the main power switch at the wall, and lock it in the OFF position. 3. ...
Dripping Prevention and ITM Heating Hood Service -- CA393-10100 Rev 00 - Page 66
A More theory
Software settings
The following software settings can be configured in the SysTab editor to support changes in the hardware configuration of your press. When installing the dripping reduction kit, set the following SysTab parameters: ● Set the parameter engineConfigTopic > ihhInstalled to HT_VER1. ● Set the parameter engineConfigTopic > feedSuctionNautilairInstalled to ...
Preventive Maintenance -- CA393-00660 Rev 08 - Page 3
... every 12 million impressions for HP Indigo WS6000 Series Digital Presses. NOTE: For HP Indigo WS6000 Series Digital Presses with press software v15.0 I-Fix 1 and above, reset the 12M IMP Counter when you are done. PM service will take place every 24 million impressions for HP Indigo WS7200 Series Digital Presses.
Estimated installation time
Estimated installation time is 6 hours.
Special jigs...
Preventive Maintenance -- CA393-00660 Rev 08 - Page 8
...the results according to HP Indigo WS6600 Digital Press Installation Manual (CA393-04361) or HP Indigo W7200 Digital Press Installation Manual (CA393-01570).
● Clear the hard drive (delete temporary and unused files) - see HP SmartStream Labels and Packaging Print Server, Powered by Esko Best Practice Guide (CA394-06791).
● Verify software configuration (HP IndigoServe, RIP, and Norton...
Preventive Maintenance -- CA393-00660 Rev 08 - Page 14
...control thermostat is approximately at the set point at 0.5°C.
● Check the state of the water filter. If the pressure drop exceeds 1 bar (10 psi), change the filter element.
ILD
● If ILD is installed...for HP
● Click Next.
Indigo WS6000 Series Digital Presses with ● Select Click Finish to confirm compilation of Customer Engineer 12M Imp maintenance.
press software ...
Preventive Maintenance -- CA393-00660 Rev 08 - Page 23
... leak
Appendix E - Replacing the Ametek blower air filter
There are two types of Ametek blower filters. Use the relevant procedure to remove the filter before installing the replacement filter.
Removing the Ametek blower filter (Type 1)
Refer below for the type of filter and follow the steps to remove the ametek blower...
Preventive Maintenance -- CA393-00660 Rev 08 - Page 24
...) as described below in
Installing an Ametek blower filter on page 23.
Removing the Ametek blower filter (Type 2)
Refer below for the type of filter and follow the steps to remove the ametek blower filter. 1. Shut down the press software. Turn off the press. 2. Insert a flat screw driver into the slot in the...
Preventive Maintenance -- CA393-00660 Rev 08 - Page 25
... blower filter as described below in Installing an Ametek blower filter on page 23.
Installing an Ametek blower filter
Follow the steps below for installing an ametek blower filter. 1. Shut down the press software. Turn off the press. 2. Insert the filter into the housing. Each pin should fit into a slot. (There are 8 pins and...
Preventive Maintenance -- CA393-00660 Rev 08 - Page 27
..., added HP Indigo W7200 Digital Press to the scope. Update of entire document content. HP Indigo W7250 Digital Press to the scope. Removal of kit and addition of inspection and cleaning of filters before replacing. Updates of part numbers. Updates of topics in tables. Line added to Ink Cabinet section. Added information about HP Indigo WS6000 Series Digital Presses with press software v15.0 I-Fix...
Blanket Creep Diagnosis and Correction - Page 9
... as follows: 1. In press Standby mode, cool the ink.
a. In the press software, go the Main Menu, Problem Handling, HP Indigo Print Care. b. Check Service Level. The Service Level panel opens. c. Select Customer Engineer. In the entry window, type PSW, then press OK. The Service panel
opens. d. Select Elements Activation, the Elements Activation panel opens. e. Select all...
Blanket Creep Diagnosis and Correction - Page 11
... less. Figure 3-7 Checking the ITM temperature
e. Close the Elements panel to disable recent activations. 4. Install the new blanket. 5. Measure the blanket position.
a. Go the System Status panel. b. Push the... Save the file. f. Restart the press software. 7. In the press software, make sure that there is no bypass on the Cold Start button. In the Service Panel, select Bypass, then Cold Start, and...
Long Term Shutdown for Indigo WS6000 Series Digital Presses and Indigo W7200 Series Digital Presses -- CA393-09200 Rev 01 - Page 7
... Digitax 9. Turn on the press and ILP (if installed). 10. Load a substrate roll on the unwinder. Load an empty core on the rewinder. 11. Replace all... Validate the ink conductivity. 14. Check that the writing head window and the IR sensors are clean. 15. Change the press ...Make sure that the press software is up-to-date. 19. Check with the Technical Group for any service notes that need to be implemented....