Lexmark 3000 Color Jetprinter driver and firmware
Drivers and firmware downloads for this Lexmark item
Related Lexmark 3000 Color Jetprinter Manual Pages
Download the free PDF manual for Lexmark 3000 Color Jetprinter and other Lexmark manuals at ManualOwl.com
Service Manual - Page 2
... respective owners.
© Copyright Lexmark International, Inc. 1997. All Rights Reserved.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS This software and documentation are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252...
Service Manual - Page 5
... and safety instructions.
2. Diagnostic Information contains error indicator table, symptom table, and service checks used to isolate failing field replaceable units (FRUs).
3. Diagnostic Aids contains tests and checks used to locate or repeat symptoms of printer problems.
4. Repair Information provides instructions for making printer adjustments and removing and installing FRUs.
5. Connector...
Service Manual - Page 11
1. General Information
The Lexmark 3000 Color Jetprinter is a personal, near laser-quality inkjet printer. The printer contains two print cartridges (color and black), which are customer replaceable supply items. A single printhead provides three colors and composite black printing. The printer also supports a black print cartridge and provides 600 X 300 dpi edge definition for professional ...
Service Manual - Page 14
...movement • Carrier stops • Carrier slams side frame
Action
Go to the 'Carrier Transport Service Check' on page 2-5.
Maintenance Station Problems
Symptom Maintenance station: • Fails to cap the...
Operator Panel
Action
Go to the 'Maintenance Station Service Check' on page 2-7.
Symptom
Paper Feed and / or Install print cartridge buttons do not operate
Busy light does not come...
Service Manual - Page 17
...:
• An open or short in the motor. • An open or short in the motor driver on the
system board. • A bind in the carrier transport mechanism. With the carrier transport motor cable disconnected from the system board, check for zero to ten (0 - 10) ohms between the following pins on the motor:
CN2...
Service Manual - Page 20
..., an open or short in the motor driver on the system board, or a bind in the paper feed mechanism. With the paper feed motor cable disconnected from the system board, check for 60 ohms (±15 ohms... motor turns in one direction only, replace the system board.
Binds in the paper feed motor or gear train can cause intermittent false paper jam errors. Remove the paper feed motor and check the shaft...
Service Manual - Page 22
...
Examine the machine for the following before you begin this service check:
• Check the entire paper path for obstructions. • Be sure the correct type of paper is being used. • Be sure the printer is installed on a flat surface.
FRU
Action
1 Large and Small Feed Rollers
Check for wear and binds...
Service Manual - Page 29
... area of NVRAM to the U.S. factory defaults. The page count and the error log do not change. Note: Factory defaults are initially set to U.S. To run the test:
1. With the printer off, press and hold the Install Print Cartridge button while turning the printer on:
2. Releasing the buttons resets NVRAM to the U.S. factory defaults.
A sheet...
Service Manual - Page 30
... the test page. To run a complete test page of black and color patterns, be sure the print cartridge is in good condition. Install a black print cartridge. To enter the test:
• Press and hold the Paper Feed button while turning the printer
on. Paper feeds from the sheet feeder and prints the test...
Service Manual - Page 31
...to make adjustments to the printer and how to remove defective... ESD-sensitive parts, follow the instructions below in addition to all the usual precautions, such as turning off power before removing logic boards:
• Keep the ESD-...
• Prevent ESD-sensitive parts from being accidentally touched by other
personnel. Install machine covers when you are not working on the machine, and do not put...
Service Manual - Page 34
... 2. Remove the rear cover. 3. Remove the sheet feeder. 4. Disconnect the power supply connector at the system board. 5. Remove the two screws that secure the carrier frame to the
base assembly. ...carrier frame and install them on the new carrier frame.
Carrier Home Sensor Removal
1. Remove the front cover. 2. Remove the rear cover. 3. Disconnect the sensor cable from the system board. 4. Remove ...
Service Manual - Page 43
5. Connectors
CN1
CN2
CN3 CN4 CN5 CN6 CN7 CN8 CN9 PH1 U14 SW1 SW2
SW3
LED1 LED2
Home Position Sensor Carrier Transport Motor Paper Feed Motor Printhead Cable 1 Printhead Cable 2 Printhead Cable 3 Printhead Cable 4 Parallel Port Power Supply EOF Sensor Code Module Power Switch Paper Feed Switch Install Print Cartridge Switch Busy Light Power-On Light
Connectors 5-1