Lexmark T522 - Optra Laser Printer driver and firmware
Drivers and firmware downloads for this Lexmark item
Related Lexmark T522 Manual Pages
Download the free PDF manual for Lexmark T522 and other Lexmark manuals at ManualOwl.com
User's Guide - Page 10
... settings from your software application or printer driver. Settings you change from the application or printer driver apply only to the job you are preparing to send to the printer. Changes made to printer settings from a software application override changes made from the printer operator panel. If you cannot change a setting from your application, use the printer operator panel or the remote...
User's Guide - Page 13
... are the settings you select for different printer functions and store in printer memory. Once stored, these settings remain active until new ones are stored or the factory defaults are restored.
Note: Settings you choose from your software application may override the settings you select from the operator panel.
Menus Disabled
If your printer is configured as a network printer available to...
User's Guide - Page 76
... is
completed, Ready is displayed.
If the messages do not appear, turn the printer off and call the Lexmark Customer Support Center.
Settings in the software application, the printer driver, or the printer utilities are overriding the settings made from the operator panel.
• Change the menu settings from the printer driver, the printer utilities, or the software application instead of the...
User's Guide - Page 77
... a serial interface:
• Make sure Honor DSR is set to Off. • Check the protocol, baud, parity, and data bit settings. The settings
on the printer and on the host computer should match.
Printer is connected to the USB Make sure you are using Windows 98, Windows 2000, Windows Me, or
port, but will not print.
another USB-capable operating system supported by Lexmark.
Print...
User's Guide - Page 78
... Print Timeout setting in the Setup Menu. Increase the setting.
Job prints from the wrong paper Check the Paper Type setting in the Paper Menu from the printer operator source or on the wrong print panel and in the printer driver. material.
Paper does not stack neatly in • Make sure the paper bail is installed.
the output...
User's Guide - Page 81
... the Quality Menu to On. • If you are using downloaded fonts, verify that the fonts are supported by the
printer, the host computer, and the software application.
Image quality is poor.
Resolution was automatically reduced. Reduce the complexity of the print job or add additional printer memory. See Res Reduced.
Part or all of the page is...
User's Guide - Page 85
...
• Refer to the drivers CD that came with your printer which contains printer drivers and utilities.
• Visit the Lexmark Web site, www.lexmark.com, for the most current printer drivers or utilities.
I need to attache a serial cable to the printer.
If you have installed an optional interface card in your printer, refer to the Setup Guide.
I can't find the printer escape Refer to the...
User's Guide - Page 112
... serial link is set up correctly and you are using the appropriate cable. • Press Go to clear the message and continue printing. The job may not print correctly. • Press Menu to open the Job Menu and reset the printer.
54 Network Software Error
54 Std Network Software Error
What these messages mean: The printer cannot establish communications with an installed network port...
User's Guide - Page 200
... includes a remote management function that lets you manipulate the font files you have
downloaded to flash memory or hard disk. See the drivers CD for more information about
MarkVision.
Printing a font sample list
To print samples of all the fonts currently available for your printer:
1 Make sure the printer power is on and the Ready status message is displayed. 2 Press...
User's Guide - Page 210
... 111 54 Parallel Error 111 54 Parallel Option Error
111 54 Serial Option Error 110 54 Standard Serial Error 110 54 Std Network Software Error
110 54 Std Par ENA Connection
Lost 111 56 Parallel Port Disabled
111 56 Serial Port Disabled 112 56 Standard Serial Disabled
112 56 Std Parallel Port Disabled
111 58 Too Many Disks Installed
112 58 Too Many Flash Options
112 58...
Quick Reference Guide - Page 2
... Symbol Set Orientation Lines per Page A4 Width Tray Renumber Auto CR after LF Auto LF after CR
Setup Menu
Printer Language Power Saver Resource Save Download Target Print Timeout Wait Timeout Auto Continue Jam Recovery Page Protect Display Language Alarm Control Toner Alarm Job Accounting
Network Menu
PCL SmartSwitch PS SmartSwitch NPA Mode Network Buffer Job Buffering Network Setup Mac Binary...
Setup Guide - Page 4
...Attach cables
4
See page 18
Verify setup
5
Network printing - page 18 Local printing - page 19
See page 21
Order of installation
2000-Sheet drawer page 3
* Option install order may be reversed.
Configure for TCP/IP
6
See page 23
Install memory and option cards
2
Optional firmware card page 13
Printer/flash memory page 12
Install printer drivers
7
See page 25
Access printer system board...
Setup Guide - Page 15
... card
Follow the instructions in this section to install an optional firmware card. The system board has one location where a firmware card can be installed.
Warning! Optional firmware cards are easily damaged by static electricity. Touch something metal on the printer before you touch a card.
Resting posts
1 Access the system board. (See page 10 for instruc-
tions.)
2 Unpack the firmware card...
Setup Guide - Page 27
...following instructions explain how to install printer
drivers on printers attached to a network.
Windows
Ports
The following network printer ports are supported:
• Microsoft IP port (Windows NT 4.0 and Windows 2000)
• Lexmark network port (Windows 95/98/Me, Windows NT 4.0, and Windows 2000)
Printer drivers
Note: Using the Lexmark T522 custom printer driver and a Lexmark network port...
Setup Guide - Page 28
... CD. Updated system and custom drivers are available on the Lexmark Web site at www.lexmark.com/drivers.
Printing methods The following network printing methods are supported:
• Direct IP printing • Shared printing (point and print, peer-to-peer)
Creating ports and installing drivers Read the detailed instructions on the drivers CD. Click View documentation and look for network printer...
Setup Guide - Page 29
... The user's guide contained in each package gives detailed instructions for installing and using Lexmark printers in UNIX environments.
You can download these printer driver packages from Lexmark's Web site at www.lexmark.com/drivers. Depending on which drivers CD shipped with your printer, you may also find the driver package you need on the CD.
NetWare
Your Lexmark T522 printer works with both...
Setup Guide - Page 30
..., such as printer status alerts.
Printer drivers The following printer drivers are supported:
• Windows system printer driver • Lexmark T522 custom printer driver System drivers are built into Windows operating systems. Custom drivers are available on the drivers CD.
Updated system and custom drivers are available at www.lexmark.com/drivers.
Installation instructions
Read the...
Setup Guide - Page 31
.... The user's guide contained in each package gives detailed instructions for installing and using Lexmark printers in UNIX environments.
All the driver packages support local printing using a parallel connection. The driver package for Sun Solaris systems also supports USB connections to Sun Ray appliances and Sun workstations.
You can download these printer driver packages from Lexmark's Web site...
Service Manual - Page 34
... x. 976 - Unrecoverable software error in Network Card x. 977 - Controller software detects that a Network Card is installed in slot x but cannot establish communications with it. 978 - Bad checksum while programming Network Card x. Replace Network Card x. 979 - Flash parts failed while programming Network Card x. If the printer is a network model, replace the controller board.
2-6 Service Manual
Service Manual - Page 116
... printer using plain paper (20 lb.).
An incorrect printer driver for the installed software can cause problems. Incorrect characters could print and the copy may not fit the page correctly.
Measure all voltages from the connector to printer ground. All voltages measured during the print cycle are measured with the controller board removed while running the print test.
2-88 Service Manual