Samsung DV45K7600EW/A3 driver and firmware
Drivers and firmware downloads for this Samsung item
Related Samsung DV45K7600EW/A3 Manual Pages
Download the free PDF manual for Samsung DV45K7600EW/A3 and other Samsung manuals at ManualOwl.com
User Manual - Page 2
... Ducting requirements Exhausting requirements Gas requirements Electrical requirements
Installation
What's included Step-by-step installation Vent blockage test Exhaust ducting guide Switching the door position
Before you start
Sort and load Functional prerequisite
Operations
Feature panel Simple steps to start Cycle overview Drying guide Special features
2 English
DV7700K-03170U-01_EN (US).indd...
User Manual - Page 4
..., caution and care when installing, maintaining and operating your dryer. Because the following operating instructions cover various models, the characteristics of your dryer may differ slightly from those described in this manual and not all warning signs may be applicable. If you have any questions or concerns, contact your nearest service center or find help...
User Manual - Page 5
... conditions will obstruct clothes dryer airflow and increase the risk of fire. • To reduce the risk of severe injury or death, follow all installation instructions. • Save these instructions.
Important safety precautions
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions...
User Manual - Page 6
... is moving. 8. Do not install or store this appliance where it will be exposed to the weather. 9. Do not tamper with internal controls. 10.Do not repair or replace any part of the appliance or attempt any service unless
specifically recommended in the user-maintenance instructions or in published userrepair instructions that you understand and...
User Manual - Page 7
...latex foam) or similarly textured rubberlike materials must not be dried on a heat setting. Heated foam rubber materials can, under certain circumstances, ignite spontaneously.
WARNING -...'s phone. Follow the gas supplier's
instructions. • If you cannot reach your gas supplier, call the fire department. • Installation and service must be performed by a qualified installer, service agency...
User Manual - Page 8
...install or store this appliance where it will be exposed to the weather. • Do not tamper with the controls. • Do not repair, replace, or attempt to service any part of the appliance unless
specifically instructed to in the user-repair instructions... or product. • Clean the lint screen before or after each load. • Keep the area around the exhaust opening and surrounding areas ...
User Manual - Page 10
... following instructions before installing the dryer, and keep this manual for future reference.
WARNING The control board and inlet valve are intentionally not grounded and may present a risk of electric shock only during servicing. Service personnel - Do not contact these parts while the appliance is energized.
Key installation requirements
• A grounded electrical outlet. • A power...
User Manual - Page 11
... requirements
Recommended
Use only for short-run installation
Weather hood type
No. of 90° elbows 0 1 2 3
4" (10.2 cm)
Rigid
Metallic flexible*
80 ft. (24.4 m) 41 ft. (12.4 m)
68 ft. (20.7 m) 37 ft. (11.2 m)
...
User Manual - Page 12
...required exhaust duct is 4 inches
(10.2 cm) in diameter. • See "Ducting requirements" in the
"Installation" section for the maximum duct length and number of bends that can be used. • The total length ...WARNING
• You must exhaust the dryer to the outside to reduce the risk of fire when you install the dryer in an alcove or closet.
• Do not use a plastic or non-metal flexible ...
User Manual - Page 13
...liquid propane) gas, it must be converted for safe and proper performance by a qualified service technician.
• A 1/2" (1.27 cm) gas supply line is recommended and must... inspect a gas appliance installation.
Commonwealth of Massachusetts installation instructions Your dryer must be installed by a licensed plumber or gas fitter. A "T" handle manual gas valve must be installed in the gas supply ...
User Manual - Page 14
Installation requirements
Installation requirements
Electrical requirements
The wiring diagram is located on the plate under the control panel or rear frame.
WARNING
&#...Revisions and local codes and ordinances. It is your responsibility to provide adequate electrical service for your dryer.
• All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 - Latest ...
User Manual - Page 15
... all grounding instructions in the ...service. Some require 120 / 208 volt, 60 Hz approved electrical service. The electric service...power supply cord from
an old dryer. The power cord electric supply wiring must be supported at the dryer cabinet by a suitable UL-listed strain relief. • Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations, (2) mobile...
User Manual - Page 16
... the main power while observing the relevant safety regulations of your area.
What's included
Make sure all the parts are included in the product package. If you have a problem with the dryer or the accessories, contact a local Samsung service center or the retailer.
01 02
03 04
05
Dryer at a glance 01 Control panel...
User Manual - Page 17
Installation
Accessories & tools (applicable models only) Accessories
Y connector Required tools
Water hose (Canadian models only)
Short water hose
Pliers
Cutting knife
Pipe wrench (gas models only)
...
User Manual - Page 18
... the door position". 3. Install the exhaust system as instructed in the "Exhaust ducting guide" section.
NOTE •... To move the dryer easily, lay two of the carton cushions from the packaging on the
floor. Tip the dryer on its side so it lies across both cushion-tops. Push the dryer so that it is near its final location, and then set...
User Manual - Page 19
Installation
STEP 3 Connect the electrical wiring
First, read through the "Electrical requirements" section, and then follow these steps.
3-wire system
1. Loosen or remove the center terminal
D
block.
2. Connect the neutral wire (white or
C
center wire) of the power cable... system, connect the ground strap to the terminal block support to ground the dryer frame to the neutral conductor.
...
User Manual - Page 20
...power cable to the screw.
CAUTION
• To connect the ground wire to the neutral position without through contact A (cabinet ground), contact a technician. This is not user serviceable... connection is required for new or remodeled construction, mobile homes, or if local codes do not permit...relief must be used. Do not loosen the nuts already installed on the terminal block. Be sure they are tight. ...
User Manual - Page 21
Installation
STEP 4 Connect the water hose (applicable models only)
The dryer must be connected to a cold water tap using the ...damaged.
4. Connect the angled end of the water hose to the filling valve at the bottom of the rear frame. Turn the coupling manually until it is tight.
5. Using pliers, tighten the coupling an additional two-thirds turn. Do not overtighten because the coupling may be...
User Manual - Page 22
Installation
Installation
Using the short hose as an extension
B A C
1. Close the cold water tap. If you have a washer cold water hose attached to the cold water faucet, unscrew and remove the hose. Then, connect the short hose (B) to the cold water tap. Turn the coupling manually...brass male end of the short hose. Turn the coupling manually until it is tight.
4. Using pliers, tighten the coupling...
User Manual - Page 37
... the dryer displays an information code, you can use Smart Care to check the status of the dryer on a smartphone. To use Smart Care, you must have the Samsung Smart Care app installed on your smartphone.
NOTE
Smart Care is optimized for Samsung Galaxy and Apple iPhones. (Not compatible with some models). Download the Samsung Smart...