ViewSonic CDP9800 driver and firmware
Related ViewSonic CDP9800 Manual Pages
Download the free PDF manual for ViewSonic CDP9800 and other ViewSonic manuals at ManualOwl.com
CDP9800 Datasheet English - Page 2
... - Unlimited Users SW-50* Trolley Cart LB-STND-003 Wall Mount WMK-047
What's in the box?
CDP9800 display, power cable, VGA cable, audio cable, USB cable, RS232 adapter, remote control with batteries, ViewSonic Wizard CD (User Guide and vController™ software)
ViewSonic Corporation's QMS & EMS have been registered to ISO 9001 & ISO 14001, respectively, by TUV NORD.
*Requires NMP-800...
CDP9800 User Guide English - Page 1
CDP9800 Commercial Display
User Guide
IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http:// www...
CDP9800 User Guide English - Page 3
... A/Class B digital device, pursuant to Part 15 of the FCC Rules, this device must be installed in computer equipment certified to comply with the Class A/Class B limits. All cables used to connect the computer and peripherals must be shielded and grounded. Operation with non-certified computers or non-shielded cables may result in interference to radio or television reception. Changes...
CDP9800 User Guide English - Page 4
...according to local law. If the batteries, accumulators and button cells included with this equipment, display the chemical symbol Hg, Cd, or Pb, then it means that the battery has a ... service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmitting antenna) that is installed outdoors is subject to licensing. The installer ...
CDP9800 User Guide English - Page 6
... monitor. • The power cable connector is the primary means of detaching the system from the power supply. The monitor should be installed close to a power outlet, which is easily ... a year because of set reliability. • If using the cooling fan continuously, it's recommended to wipe holes a minimum of once a month. • When installing the remote control batteries; - Align the...
CDP9800 User Guide English - Page 7
...; Avoid displaying fixed patterns on the monitor for long periods of time to avoid image
persistence (after image effects). • Get regular eye checkups.
Ergonomics
To realize the maximum ergonomic benefits, we recommend the following: • Use the preset Size and Position controls with standard signals. • Use the preset Color Setting. •...
CDP9800 User Guide English - Page 8
... PC 9 3.2.1. Using VGA input 9 3.2.2. Using DVI input 9 3.2.3. Using HDMI input 9 3.2.4. Using HDMI input 10 3.3. Connecting Audio Equipment........ 10 3.3.1. Connecting external speakers 10 3.3.2. Connecting an external audio device 10 3.4. Connecting Multiple Displays in a Daisy-chain Configuration 11 3.4.1. Display control connection.. 11 3.4.2. Digital video connection...... 11 3.5. IR...
CDP9800 User Guide English - Page 11
...display
• CD ROM
• Remote control with AAA batteries
• Power cord (1.8 m)
Video Signal Cable (D-SUB to D-SUB Cable)
• VGA cable (1.8 m)
• RS232 cable (3.0m)
• Quick Start Guide
RS232 Cable
NORMAL ID
SOURCE
FORMAT
LIST
INFO
ADJUST
OPTIONS VOL
ID SET
ENTER
Remote Control...the display.
1.3. Installation Notes • Due to the high power consumption...
CDP9800 User Guide English - Page 12
... keep a clear safety area under the display while using the eye bolt.
1.4.1. VESA Grid CDP9800
800(H) x 500(V) mm
Caution:
To prevent the display from falling:
• For wall or ceiling installation, we recommend installing the display with metal brackets which are commercially available. For detailed installation instructions, refer to the guide received with the respective bracket.
•...
CDP9800 User Guide English - Page 13
.... 1. Remove the table stand, if attached. 2. When facing the display at the back, rotate 90 degrees anticlockwise, the input/output terminals should at
the top and right side.
90
90
NOTE: When installing the display on a wall, please consult a professional technician for proper installation. We accept no liability for installations not performed by a professional technician.
3
CDP9800 User Guide English - Page 17
... it dry
immediately. • Avoid exposure to heat and steam. • Other than to install the batteries, do not open the remote control.
2.3.4. Operating range of the remote control
Point the top of the remote control toward the display's remote control sensor when pressing a button.
Use the remote control within a distance of less than 5m (pull the lens down and use the...
CDP9800 User Guide English - Page 29
... display.
Network settings
DHCP IP address Subnet mask Default gateway MAC address [ SET ]
Enable 0 000 0 000 0 000 00:24:67:30:07:3E
• DHCP - Choose to enable or disable the DHCP function. If enabled, the display will be assigned IP address, Subnet mask and Default gateway automatically. If disabled, you will be prompted to enter the following values manually...
CDP9800 User Guide English - Page 35
... .asf .wma .wav (PC) .aif (mac) .aiff (mac) .aac .mp4 .m4a .pls .m3u .m4a
Container MP3 WMA
(V2 up to V9.2) WMA Pro LPCM LPCM
AAC
Playlists M4A
Video codec -
-
-
Maximum resolution
-
-
-
Frequency (kHz) 48
48
96 192
192
Max.Bit Rate (Mbps) 384
192
768 768
768
Audio codec MPEG-1, 2, 2.5 L3
WMA WMA...
CDP9800 User Guide English - Page 36
...
For DP/ HDMI
Video timing support (HDMI/DVD HD/DVI):
480i, 480p, 576i, 576p, 720p, 1080i, 1080p, 4Kx2K (except DVI & DVD HD).
NOTES:
• The PC text quality is optimum in HD 1080 mode (1920 x 1080, 60Hz).
• Your PC display screen might appear different depending on the manufacturer (and your par ticular version of Windows).
• Check...
CDP9800 User Guide English - Page 41
... Protocol
10.1. Introduction This document describes the hardware interface spec and software protocols of RS232 interface communication between ViewSonic Commercial TV / Digital Signage and PC or other control unit with RS232 protocol.
The protocol contains three sections command: • Set-Function • Get-Function • Remote control pass-through mode ※ In the document below, "PC...
CDP9800 User Guide English - Page 55
... as "image burn-in" which results when a static image is displayed on the product for an extended period of time. 4. Removal, installation, one way transportation, insurance, and set-up service charges.
How to get service: 1. For information about receiving service under warranty, contact ViewSonic Customer Support (Please
refer to Customer Support page). You will need to provide your product...
CDP9800 User Guide English - Page 57
... image is displayed on the product for an extended period of time. 4. Removal, installation, one way transportation, insurance, and set-up service charges.
How to get service: For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the attached Customer Support page). You will need to provide your product's serial number, so please record the...