Asus PR-DLS driver and firmware
Related Asus PR-DLS Manual Pages
Download the free PDF manual for Asus PR-DLS and other Asus manuals at ManualOwl.com
PR-DLS User Manual - Page 12
PR-DLS specifications summary
BIOS features
Form Factor Support CD contents
4Mb Flash ROM, Award BIOS with ACPI, DMI, Green, PnP features, and Enhanced Server BIOS features
Extended ATX form factor: 12 in x 13 in (30.5 cm x 33 cm)
Device drivers Management software Utilities Contact information
* Specifications are subject to change without notice.
xii
PR-DLS User Manual - Page 19
... and components are based on the following high-level goals: support for Plug-and-Play compatibility and power management for configuring and managing all system components, 32-bit device drivers, and installation procedures for Windows NT/2000/XP. Color-coded connectors and descriptive icons make identification easy as required by the PC '99 specification.
ASUS PR-DLS motherboard user guide
1-5
PR-DLS User Manual - Page 37
...Configuring an expansion card
After installing the expansion card, configure the it by adjusting the software settings.
1. Turn on the system and change the necessary BIOS settings, if any. See Chapter 4 for information on BIOS setup.
2. Assign an IRQ to the card. Refer to the tables on the next page. 3. Install the software drivers for the expansion card.
ASUS PR-DLS motherboard user guide
2-11
PR-DLS User Manual - Page 59
... computer from the floppy disk.
BIOS setup must specify "Floppy" as the first item in the boot sequence.
4. In DOS mode, type A:\AFLASH to run AFLASH.
If the word "unknown" appears after Flash Memory:, the memory chip is either not programmable or is not supported by the ACPI BIOS and therefore, cannot be programmed by the Flash Memory Writer utility.
ASUS PR-DLS motherboard user guide...
PR-DLS User Manual - Page 63
... to enable the security password feature or make changes to the power management settings. This requires you to reconfigure your system using the BIOS Setup program so that the computer can recognize these changes and record them in the CMOS RAM of the Flash ROM.
The Flash ROM on the motherboard stores the Setup utility. When you start up the computer, the system provides you...
PR-DLS User Manual - Page 80
... system time updated even when the computer enters suspend mode. In Windows 3.x and Windows 95, you need to install Windows with the APM feature. In Windows 98 or later, APM is automatically installed as indicated by a battery and power cord icon labeled "Power Management" in the Control Panel. Select the item "Advanced" in the Power Management Properties dialog box.
4-22
Chapter 4: BIOS Setup
PR-DLS User Manual - Page 93
... or else the new driver installed from the LSI driver disk will not be recognized.
Even if you did not press F6, you are still allowed to load additional drivers later in the installation process. However, any drivers loaded during Windows NT Setup are not immediately recognized and no devices controlled by that driver are available during Windows NT Setup.
ASUS PR-DLS motherboard user guide
5-1
PR-DLS User Manual - Page 94
... perform a manual selection. A screen displays the message "Setup has recognized the following mass storage devices in your computer...".
4. With floppy disk 2, there is an initial setup screen that prompts you to continue by pressing Enter.
5. Press S to skip mass storage device detection. If you pressed Enter, the installation program scans for SCSI adapters and finds the LSI PCI driver 53C1010R...
PR-DLS User Manual - Page 95
...insert the appropriate LSI driver disk containing the Windows NT driver required to support your LSI adapter(s). The path to copy manufacturer's files is: A:\WINNT\MINIPORT and select OK.
8. Depending on the driver being installed, Symbios Ultra3 PCI SCSI Driver is shown highlighted on the Install Driver menu. If it is not highlighted, select it. Choose OK.
ASUS PR-DLS motherboard user guide
5-3
PR-DLS User Manual - Page 96
...Preparing the Intel 82551QM/82544GC LAN Driver Disk
Windows NT 4.0 does not have the drivers for the Intel 82551QM and Intel 82544GC LAN controllers. Before installing Windows NT 4.0, copy the LAN drivers from the PR-DLS support CD into a floppy disk.
Prepare one blank formatted high density floppy disk before proceeding.
1. Insert the PR-DLS support CD into the CD-ROM drive. 2. Run the dcreat.exe...
PR-DLS User Manual - Page 101
...recognized and no devices controlled by that driver are available during Windows 2000 Setup.
3. When prompted for the manufacturer-supplied hardware support disk, insert the appropriate LSI driver disk containing the Windows 2000 driver required to support your LSI adapter(s) and press Enter. The LSI Driver disk is creating prior to installing Windows 2000.
ASUS PR-DLS motherboard user guide
5-9
PR-DLS User Manual - Page 102
... of the SCSI and RAID controllers line. Find the adapter desired for the driver upgrade and double click on the entry. Click on the Driver tab.
5. Information on the currently installed driver is displayed, and additional driver details can be viewed by clicking the Driver Details.... button.
6. To update the existing driver, click the Update Driver button. The Upgrade Device Driver Wizard begins...
PR-DLS User Manual - Page 103
... downloaded from the LSI Logic web site at www.lsilogic.com may not be digitally signed.
12. The system will load the driver from the LSI driver disk. A message box may appear indicating that the target (existing) driver is newer than the source (upgrade) driver. Click No to cancel the driver upgrade at this point or click Yes to continue the installation.
ASUS PR-DLS motherboard...
PR-DLS User Manual - Page 105
When done, your Computer Management window shows the installed LAN adapters.
3. Highlight the Intel(R) 82554GC-based Network Connection, click the right mouse button, and select Properties to display the following.
ASUS PR-DLS motherboard user guide
5-13
PR-DLS User Manual - Page 106
... Ethernet Controller, then click the right mouse button and
select Properties. 6. Select the Driver tab and click on Update Drivers. 7. Click Next. Select Display a list of the known drivers for this device ... 8. Select Network adapters under Hardware Type, and click Next. 9. Click Have Disk..., then insert the LAN driver disk. 10. Follow the succeeding instructions to complete the installation...
PR-DLS User Manual - Page 107
...
Windows 2000 system can automatically recognize the ATI RAGE XL PCI driver during system installation. You do not need to load any driver for supporting the onboard ATI RAGE XL graphics controller chipset.
5.2.4 Enabling ATA100 Feature in Windows® 2000
To enable the ATA100 feature under Windows 2000, you need to upgrade to Windows 2000 Service Pack 2.
ASUS PR-DLS motherboard user guide...
PR-DLS User Manual - Page 116
... scanning is complete, the Identified Devices screen appears.
12. Press F2_Continue. The message "Loading driver..." appears followed by messages about the drivers that are required to boot your system. After a few seconds, the Boot Solaris screen appears.
13. At the Boot Solaris screen, select the device controller attached to the device that contains your install medium, i.e., CD-ROM or Network...
PR-DLS User Manual - Page 118
... new or updated drivers, the newly supported hardware devices should be installed and configured according to the instructions in the corresponding Device Reference Page, if any. See the Device Reference Manual for Solaris (Intel Platform Edition). When the Solaris Intel Platform Edition software is already installed, the simplest way to add new or updated drivers is to install the Driver ITU...
PR-DLS User Manual - Page 122
... procedure assumes SCO UNIX is already installed on a hard disk drive. This installation is necessary to build a new UNIX kernel that includes the proper LSI host adapter driver. The basic steps for accomplishing this are outlined below. For more details on UNIX installation, refer to the SCO UNIX System Administrator's Reference Manual.
1. The SCO OpenServer 5 system automatically creates...
PR-DLS User Manual - Page 123
... 5.0.6 system can correctly recognize Intel 82551QM/ 82544GC network controller during installation. User doesn't need to load or modify the network driver for the onboard LAN device.
You can find the Intel 82551QM/82544GC Network driver from PR-DLS support CD at:
\Drivers\Lan\UNIX\SCO5
Instructions for Installing the eeE Driver for SCO OpenServer
1. Copy the eee.vol file to any directory, say...