Asus V3-M2NC61S - V Series - 0 MB RAM driver and firmware
Drivers and firmware downloads for this Asus item
Related Asus V3-M2NC61S Manual Pages
Download the free PDF manual for Asus V3-M2NC61S and other Asus manuals at ManualOwl.com
V3-M2NC61S User's Manual for English Edtion - Page 1
U2811
V-Series M2NC61S
ASUS PC (Desktop Barebone)
Installation Manual
V3-M2NC61S User's Manual for English Edtion - Page 2
...
USB 2.0 ports Center/subwoofer port
Microphone port Line Out port Line In port
Expansion slot Metal brackets
3.5-inch drive bay cover Headphone port Microphone port USB 2.0 ports HDD LED Reset button
Power button
Power supply fan Cover screw
Chassis fan vents VGA port IEEE 1394 port Side speak out port LAN (RJ-45) port Rear speak out port
Cover screw Metal bracket lock
Installation manual
V3-M2NC61S User's Manual for English Edtion - Page 3
...8 M2N-NM
10
12
11
2
3 1
4
1. Front panel cover 2. 5.25-inch optical drive bays 3. Hard disk drive bay 4. Floppy disk drive bay 5. Power supply unit 6. CPU socket 7. DIMM sockets
8. ASUS motherboard 9. PCI Express x16 slot 10. PCI Express x1 slot 11. PCI slots 12. Metal bracket lock
Selecting the voltage
The system's power supply unit has a 115 V/230 V voltage selector switch located beside...
V3-M2NC61S User's Manual for English Edtion - Page 4
... Pull the side cover toward the rear panel until its hooks disengage
from the chassis tabs. Set the side cover aside. 3. Locate the front panel assembly hooks, then lift them until they...Remove the front panel assembly, then set aside.
4 3
Air duct
1
4
2
3
1
4
2
Chassis tab holes
Installing a CPU
To install a CPU: 1. Locate the CPU socket,then
lift the socket lever to a 90º100º...
V3-M2NC61S User's Manual for English Edtion - Page 5
... on the retention mechanism to secure the heatsink and fan to the module base.
5. When the fan and heatsink assembly is in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN.
CPU Fan CPU Heatsink
Retention bracket
Retention bracket lock
3
Retention Module Base
1 4
2 5
Installation manual
V3-M2NC61S User's Manual for English Edtion - Page 6
... the retaining clips snap inward.
• Unplug the power supply before adding or removing DIMMs. Failure to do so may cause damage to the motherboard and/or components.
• A DDR2 DIMM is ...keyed with a notch so that it fits in only one direction. Do not force a DIMM into a socket to avoid damaging the DIMM.
Installing an expansion card
...
V3-M2NC61S User's Manual for English Edtion - Page 7
Installing storage drives
Optical drive
1. Place the chassis upright, then
remove the upper 5.25" drive
3
bay metal plate cover.
2. Insert the optical drive to the bay, then carefully push the drive until its screw holes align with the holes on the bay.
3. Secure the optical drive with two screws on both sides of the bay.
4. Connect the IDE (A) and power (B) plugs to connectors...
V3-M2NC61S User's Manual for English Edtion - Page 8
... the SATA signal and power plugs to
SATA
IDE
the connectors at the back of
the drive.
For IDE HDD: Connect the IDE signal and power plugs to the connectors at the back of the drive.
Removing the bay covers and reinstalling the
front panel assembly and side cover
If you installed an optical and/or floppy disk drive, remove...