Lexmark M1145 driver and firmware
Related Lexmark M1145 Manual Pages
Download the free PDF manual for Lexmark M1145 and other Lexmark manuals at ManualOwl.com
Card Stock & Label Guide - Page 2
... errors...services, except those expressly designated by the manufacturer, are the user's responsibility.
For Lexmark technical support, visit http://support.lexmark.com. For information on supplies and downloads, visit www.lexmark.com.
© 2012 Lexmark International, Inc. All rights reserved.
Trademarks Lexmark, Lexmark... the Commercial Computer Software and Commercial Software Documentation are ...
Card Stock & Label Guide - Page 10
...storage or transportation environment is very different from the printer...load it in the printer, the stock may develop uneven moisture content that can cause curl. Prior to loading...40-60%. Lexmark printers are designed ...card stock design. When designing labels, round all corners to prevent delamination of the labels, and avoid cuts through the liner (anvil cuts). Back splits and pop‑out windows...
Card Stock & Label Guide - Page 11
...‑cut guidelines for your printer, locate your printer in the "Printer specifications" chapter.
Debossing and embossing... do not warrant uninterrupted or error‑free operation of a product. Warranty service does not include repair of failures... (non‑Lexmark) servicer • operation of a product beyond the limit of its duty cycle • failure to have installed a maintenance kit...
Card Stock & Label Guide - Page 22
...recommend testing any material with your application and printer before purchasing large quantities. To use the duplex label application, you must install a special fuser wiper.
Printer
Fuser wiper part number
S1855, T612, T614... the media on the guide surface that provides the best support.
The incidence angle of the leading edge of the media as it touches the primary guide surface should be no ...
Card Stock & Label Guide - Page 26
...
215.9 mm (8.5 in.) at leading edge 279.4 mm (11 in.) at driver edge
Using cut sheet labels with adhesive applied to the edge of the sheet will contaminate your printer and your cartridge and could void your printer and cartridge warranties.
When using pressure‑sensitive materials without zone coating, choose butt cut...
Card Stock & Label Guide - Page 27
...
Leading Edge 8.5 in. 215.9 mm
Waste strip 0.25 in (6.35 mm)
Non-print area
0.33 in. 8.38 mm 0.5 in. Top perforation 12.7 mm
Waste strip
Driver edge 11 in. 279.4 mm
0.06 in. 1.6 mm
Perforation end Liner edge
0.33 in. 8.38 mm
Non-print area
0.25 in.
6.35 mm Non-print...
Card Stock & Label Guide - Page 29
...printers, which use a different paper picking mechanism.
0.094 in. 2.4 mm
Leading Edge 8.5 in. 215.9 mm
Liner edge Stripped edge
0.125 in. 3 mm
Non-print area
0.79 in. 20 mm
0.33 in. 8.38 mm
Top perforation
Driver...Cut sheet paper labels
• Generally, cut sheet paper labels work well with your printer. • Coating or sizing to make the paper liquid‑resistant decreases toner ...
Card Stock & Label Guide - Page 31
...are similar to vinyl labels.
• It is recommended that when you run vinyl labels, you install a special oil fuser cleaner, P/N 99A0725 or 40X2665.
When you order a new cartridge, be... portion
feeds into the printer first.
• Due to the unique construction of integrated forms, you may experience stacking problems in the output bin.
Contact your Lexmark marketing representative if you ...
Card Stock & Label Guide - Page 45
... the Software and Documentation CD.
Card stock and label guidelines
When printing on labels:
• Print samples on the labels being considered for use before buying large quantities. • Use only label sheets that have no gaps between the labels.
Acceptable labels
Unacceptable labels
• From the printer control panel or from MarkVision Professional, set...
Card Stock & Label Guide - Page 48
... feed reliability. Contact your local service representative for ordering information.
If you print large quantities of labels or other glossy print media, replace the fuser housing with a web oiler field upgrade kit (P/N 12G6307 for a 115 V printer, P/N 12G6308 for a 220 V printer).
When printing on labels:
• Using the printer operator panel, set the Paper Type to Labels...
Card Stock & Label Guide - Page 54
... optimize feed reliability. If you print large quantities of labels or other glossy print media, then install a dry web cleaner upgrade kit (P/N 40X1856). Contact your local service representative for ordering information.
When printing on labels:
• From the printer control panel, set Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels...
Card Stock & Label Guide - Page 55
... optimize feed reliability. If you print large quantities of labels or other glossy print media, then install a dry web cleaner upgrade kit (P/N 40X1856). Contact your local service representative for ordering information.
When printing on labels:
• From the printer control panel, set Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels...
Card Stock & Label Guide - Page 59
....
• Download the vinyl file, vinyl8ppm.npa, from our FTP site and send it to the printer (copy the file to the printer
port).
When printing on card stock:
• We recommend using Springhill Index Plus 90 lb card stock. • For the best print quality, always set the Paper Type to Card Stock in the Paper Menu.
Lexmark C920...
Card Stock & Label Guide - Page 140
...printer User's Guide on the publications CD.
Media specifications
Labels
Thickness:
0.102-0.305 mm (0.004-0.012 in.)
Smoothness:
50-300* Sheffield
* 50-150 Sheffield is optimal. This printer may support... install a dry web cleaner upgrade kit (P/N 40X1856). Contact your local service representative for ordering information.
When printing on labels:
• From the printer control panel, set ...
Card Stock & Label Guide - Page 154
... later is required to use the 4039 cartridges in your Optra and Optra plus printer. Print the menus page from the Tests Menu to determine the level of engine code installed in your printer. Contact Lexmark customer support if you need assistance upgrading to a higher level.
• Always use the fuser cleaners that come with the...
Connection Guide - Page 1
...; For Windows operating systems, the printer drivers and utilities are supported in both 32‑ and 64‑bit versions, and can be
installed using the Software CD.
• For drivers and utilities that are compatible with Mac OS X version 10.4 or later, visit http://support.lexmark.com. • For specific supported Linux operating system versions, visit http://support.lexmark.com. •...
Connection Guide - Page 2
... then follow the instructions on the computer screen.
Installing the printer locally (Windows)
Updates for the printer software may be available on the Lexmark Web site at http://support.lexmark.com.
What is local printing?
Local printing means printing to a locally attached printer (a printer that is connected directly to your computer with a USB or parallel cable). When setting up this type of...
Connection Guide - Page 3
Connection Guide
Page 3 of 6
4 Click Have Disk, and then specify the location of the printer software.
Note: The path should be similar to D:\Drivers\Print\GDI\, where D is the letter of your drive that contains the software installer package.
5 Click OK, and then follow the instructions on the computer screen.
Installing the printer on a network (Windows)
What is network printing?
In Windows ...
Connection Guide - Page 4
... Windows 7 or earlier
a Click or click Start, and then click Run. b In the Start Search or Run dialog, type D:\setup.exe. c Press Enter or click OK.
Note: D is the letter of your CD or DVD drive.
4 Click Install, and then follow the instructions on the computer screen. 5 Select Ethernet connection, and then click Continue. 6 Attach the Ethernet cable to...
Connection Guide - Page 5
... & Scan > Open Print Queue • System Preferences > Print & Fax > Open Print Queue 3 Verify that the print queue was created.
Installing the printer on an Ethernet network (Macintosh only)
1 Install the printer driver on the computer. a Download the driver at http://support.lexmark.com. b Double‑click the installer package for the printer, and then follow the instructions on the computer...