Dell Precision T5610 driver and firmware
Related Dell Precision T5610 Manual Pages
Download the free PDF manual for Dell Precision T5610 and other Dell manuals at ManualOwl.com
Owners Manual - Page 2
... Association (BDA) and licensed for use on discs and players. The Bluetooth® word mark is a registered trademark and owned by the Bluetooth® SIG, Inc. and any use of such mark by Dell Inc. is under license. Wi-Fi® is a registered trademark of Wireless Ethernet Compatibility Alliance, Inc. 2013 - 09 Rev. A00
Owners Manual - Page 3
... Computer...6
2 Removing and Installing Components 7
Recommended Tools...7 System Overview...7 Removing the Power Supply Unit (PSU)...8 Installing the Power Supply Unit (PSU)...9 Removing the Cover...9 Installing the Cover...10 Removing the Front Bezel...10 Installing the Front Bezel...11 Removing the Optical Drive ...11 Installing the Optical Drive ...13 Removing the Hard Drive...13 Installing...
Owners Manual - Page 4
......33 Removing the System Board...33 Installing the System Board...35 System Board Components...36
3 Additional Information...39
Memory Module Guidelines...39 Power Supply Unit (PSU) Lock...39
4 System Setup...41
Boot Sequence...41 Navigation Keys...41 System Setup Options...42 Updating the BIOS ...49 System and Setup Password...50
Assigning a System Password and Setup Password 50 Deleting or...
Owners Manual - Page 5
... Off Your Computer).
CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device. 3. Disconnect all network cables from the computer. 4. Disconnect your computer and all attached devices from their electrical outlets. 5. Press and hold the power button while the computer is unplugged to ground the system board. 6. Remove the...
Owners Manual - Page 6
... system, press and hold the power button for about 6 seconds to turn them off.
After Working Inside Your Computer
After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer.
1. Replace the cover. CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the...
Owners Manual - Page 7
2
Removing and Installing Components
This section provides detailed information on how to remove or install the components from your computer.
Recommended Tools
The procedures in this document may require the following tools: • Small flat-blade screwdriver • Phillips screwdriver • Small plastic scribe
System Overview
Figure 1. Inside View of the T5610 Computer 7
Owners Manual - Page 9
Installing the Power Supply Unit (PSU)
1. Hold the PSU handle and slide the PSU into the computer. 2. Follow the procedures in After Working Inside Your Computer.
Removing the Cover
1. Follow the procedures in Before Working Inside Your Computer. 2. Lay down the computer on its side with the latch facing up.
3. Lift up the cover-release latch.
4. Lift...
Owners Manual - Page 10
Installing the Cover
1. Place the computer cover on the chassis. 2. Press down on the computer cover until it clicks into place. 3. Follow the procedures in After Working Inside Your Computer.
Removing the Front Bezel
1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the cover. 3. Gently pry the front bezel retention clips away from the...
Owners Manual - Page 11
...bezel towards the computer to engage the front-bezel retention clips until they click into place. 3. Install the cover. 4. Follow the procedures in After Working Inside Your Computer.
Removing the Optical Drive
1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the cover. 3. Disconnect the data and power cables from the optical drive.
4. Unthread the cables from the latches...
Owners Manual - Page 13
.... 2. Press on the clasp to release the latch and thread the cables into the holder. 3. Connect the power cable to the back of the optical drive. 4. Connect the data cable to the back of the optical drive. 5. Install the cover. 6. Follow the procedures in After Working Inside Your Computer.
Removing the Hard Drive
1. Follow the procedures in Before Working Inside Your...
Owners Manual - Page 15
... the hard-drive caddy.
Installing the Hard Drive
1. If a 2.5-inch hard drive is installed on the computer, place the hard drive on the hard-drive caddy and tighten the screws to secure the hard drive.
2. Press in on the latches of the hard-drive cage and slide it inside the compartment. 3. Connect the hard-drive power supply cable. 4. Connect the hard-drive data cable. 5. Install the...
Owners Manual - Page 16
... to the hard drive.
Installing the Thermal Sensor
NOTE: The thermal sensor is an optional component and your computer may not ship with it. 1. Connect the thermal sensor to the component that you wish to monitor the temperature, and secure it with the
latch. 2. Connect the thermal sensor cable to the system board. 3. Install the cover...
Owners Manual - Page 18
... the screws securing the I/O panel to the chassis 3. Attach the cables to the I/O panel. 4. Slide the USB 3.0 module in its slot. 5. Tighten the screws securing the USB 3.0 module to the I/O panel. 6. Install:
a) front bezel b) cover 7. Follow the procedures in After Working Inside Your Computer.
Removing the Air Tunnel
NOTE: The air tunnel is an optional...
Owners Manual - Page 19
... Install:
a) optical drive b) cover 4. Follow the procedures in After Working Inside Your Computer.
Removing the Memory
1. Follow the procedures in Before Working Inside Your Computer. 2. Remove:
a) cover b) air tunnel (if available) 3. Press down on the memory-securing clips on each side of the memory module, and lift the memory module upwards to remove it from the computer.
Installing the Memory...
Owners Manual - Page 20
... board. 2. Press the coin-cell battery downward until the release latch springs back into place and secures it. 3. Install:
a) cover b) air tunnel (if available) 4. Follow the procedures in After Working Inside Your Computer.
Removing the Heatsink
1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the cover. 3. Disconnect the heatsink cable from the system board...
Owners Manual - Page 22
... the captive screws to secure the heatsink to the system board. 3. Connect the heatsink cable to the system board. 4. Install the cover. 5. Follow the procedures in After Working Inside Your Computer.
Removing the Heatsink Fan
1. Follow the procedures in Before Working Inside Your Computer. 2. Remove:
a) cover b) heatsink 3. Slide out the grommets that secure the heatsink fan...
Owners Manual - Page 23
4. Slide the heatsink fan from the heatsink assembly.
Installing the Heatsink Fan
1. Slide the heatsink fan into heatsink assembly. 2. Plug in the grommets to secure the heatsink fan to the heatsink assembly. 3. Install:
a) heatsink b) cover 4. Follow the procedures in After Working Inside Your Computer.
Removing the Processor
1. Follow the procedures in Before Working Inside Your...
Owners Manual - Page 49
... the log.
• Clear Log
Updating the BIOS
It is recommended to update your BIOS (system setup), on replacing the system board or if an update is available. For laptops, ensure that your computer battery is fully charged and connected to a power outlet
1. Restart the computer. 2. Go to dell.com/support. 3. If you have your computer's Service Tag or Express Service Code:
NOTE: To locate the...
Owners Manual - Page 50
... your download method below window; click Download File. The File Download window appears.
12. Click Save to save the file on your computer. 13. Click Run to install the updated BIOS settings on your computer.
Follow the instructions on the screen.
System and Setup Password
You can create a system password and a setup password to secure your computer.
Password Type System password Setup password...
Owners Manual - Page 51
... cover.
NOTE: If you assign a new system and/or setup password with the PSWD jumper installed, the system disables the new password(s) the next time it boots. 6. Connect the computer to the electrical outlet and power-on the computer. 7. Power-off the computer and disconnect the power cable from the electrical outlet. 8. Remove the cover. 9. Replace the jumper on the pins...