HP SignagePlayer mp8000r driver and firmware
Drivers and firmware downloads for this Hewlett-Packard item
Related HP SignagePlayer mp8000r Manual Pages
Download the free PDF manual for HP SignagePlayer mp8000r and other HP manuals at ManualOwl.com
Illustrated Parts & Service Map: HP SignagePlayer mp8000R Small Form Factor - Page 3
... models) • Chassis serial number
• Processor type/speed/stepping • Asset tracking number
• Cache size (L1/L2)
• ME firmware version
• Installed memory size/speed/ • Management node
channels
• Integrated MAC Address
About - Displays copyright notice.
Set Time and Date - Allows you to set system time and date.
Flash System ROM - Allows you to...
Illustrated Parts & Service Map: HP SignagePlayer mp8000R Small Form Factor - Page 4
... system board problem.
501-Display Adapter Failure
Graphics display controller.
1. Reseat graphics card. 2. Clear CMOS. 3. Check monitor connection. 4. Replace graphics card.
1720-SMART Hard Drive Hard drive is about to fail. Detects Imminent Failure
1. Determine if hard drive is giving correct error message. Enter Computer Setup and run the Drive Protection System test under Storage > DPS...
Maintenance & Service Guide: HP SignagePlayer mp8000R and mp8000s - Page 6
... 39 HP Business PC Security Lock 39 Front Bezel Security 41 Computer Access Panel ...43 Front Bezel ...44 Bezel Blanks ...45 Installing Additional Memory 46 DIMMs ...46 DDR3-SDRAM DIMMs 46 Populating DIMM Sockets 47 Installing DIMMs ...48 Expansion Cards ...51 Cable Management ...56 Cable Connections 57 Drives ...58 Drive Positions ...58 Installing and Removing Drives 59 System Board Drive...
Maintenance & Service Guide: HP SignagePlayer mp8000R and mp8000s - Page 15
... method. The range of USB flash devices available on the market constantly changes. Not all USB flash devices have been tested with the HP SignagePlayer Imaging Tool.
Getting Started
Three deployment options are supported by this utility. You can choose to do one or both of the following: ● Create a bootable flash image on a USB flash device (such as a drive key). ● Use the...
Maintenance & Service Guide: HP SignagePlayer mp8000R and mp8000s - Page 16
... copied to it. To prevent loss of data, be sure that you have saved any usercreated data from the flash drive. During the first restart of the SignagePlayer following the restore process, there may be a delay of approximately 5-10 minutes to unbundle the software before the Windows desktop is displayed.
Formatting a USB Flash Device
1. Connect your USB flash device. Ensure that only one USB flash...
Maintenance & Service Guide: HP SignagePlayer mp8000R and mp8000s - Page 21
... family name and version) ● Chassis serial number ● Asset tracking number ● ME firmware version ● Management mode
About
Displays copyright notice.
Set Time and Date Allows you to set system time and date.
Flash System ROM
Allows you to update the system ROM with a BIOS image file located on a USB flash media device or CD-ROM.
Replicated Setup
Save to Removable...
Maintenance & Service Guide: HP SignagePlayer mp8000R and mp8000s - Page 24
... speed. Some drive and cable combinations may not run reliably at 3.0 Gpbs.
NOTE: eSATA is not available on USDT systems.
SATA Emulation
Allows you to choose how the SATA controller and devices are accessed by the operating system. There are three supported options: IDE, RAID, and AHCI.
IDE (default option) - This is the most backwards-compatible setting of the three...
Maintenance & Service Guide: HP SignagePlayer mp8000R and mp8000s - Page 27
... Ports ◦ USB Port 1 ◦ USB Port 2
Slot Security
Allows you to disable any PCI or PCI Express slot
Network Service Boot
Enables/disables the computer's ability to boot from an operating system installed on a network server. (Feature available on NIC models only; the network controller must be either a PCI expansion card or embedded on the system board.)
System IDs
Allows you to set...
Maintenance & Service Guide: HP SignagePlayer mp8000R and mp8000s - Page 31
... cause the system to display a message before loading option ROMs. (This feature is supported on some models only.)
● Remote Wakeup Boot Source (remote server/local hard drive).
● After Power Loss (off/on/previous state): Setting this option to:
◦ Off-causes the computer to remain powered off when power is restored.
◦ On-causes the computer to power on automatically as soon...
Maintenance & Service Guide: HP SignagePlayer mp8000R and mp8000s - Page 32
... onboard system devices (diskette controller, serial port, or parallel port).
● Lists currently installed PCI devices and their IRQ settings.
● Allows you to reconfigure IRQ settings for these devices or to disable them entirely. These settings have no effect under an ACPI-based operating system.
PCI VGA Configuration
Displayed only if there are multiple PCI video adapters in the...
Maintenance & Service Guide: HP SignagePlayer mp8000R and mp8000s - Page 41
... guidelines listed above will still apply.
● Keep liquids away from the computer and keyboard. ● Never cover the ventilation slots on the monitor with any type of material. ● Install or enable power management functions of the operating system or other software, including
sleep states.
Routine Care
General Cleaning Safety Precautions
1. Never use...
Maintenance & Service Guide: HP SignagePlayer mp8000R and mp8000s - Page 58
... the slowest DIMM in the system.
Installing DIMMs
CAUTION: You must disconnect the power cord and wait approximately 30 seconds for the power to drain before adding or removing memory modules. Regardless of the power-on state, voltage is always supplied to the memory modules as long as the computer is plugged into an active AC outlet...
Maintenance & Service Guide: HP SignagePlayer mp8000R and mp8000s - Page 95
... to them may require replacing the system board. NOTE: After installing a new processor onto the system board, always update the system ROM to ensure that the latest version of the BIOS is being used on the computer. The latest system BIOS can be found on the Web at: http://h18000.www1.hp.com/support/files.
Power Supply
WARNING! To reduce potential safety issues...
Maintenance & Service Guide: HP SignagePlayer mp8000R and mp8000s - Page 114
... of the power-on state, voltage is always supplied to the memory modules as long as the computer is plugged into an active AC outlet. Adding or removing memory modules while voltage is present may cause irreparable damage to the memory modules or system board. The memory module sockets have gold-plated metal contacts. When upgrading the memory, it...
Maintenance & Service Guide: HP SignagePlayer mp8000R and mp8000s - Page 131
... are very fragile and any damage to them may require replacing the system board. NOTE: After installing a new processor onto the system board, always update the system ROM to ensure that the latest version of the BIOS is being used on the computer. The latest system BIOS can be found on the Web at: http://h18000.www1.hp.com/support/files.
Processor 121
Maintenance & Service Guide: HP SignagePlayer mp8000R and mp8000s - Page 165
... hard drives installed in some computers. DPS is designed to help diagnose problems that might result in unwarranted hard drive replacement. When these systems are built, each installed hard drive is tested using DPS, and a permanent record of key information is written onto the drive. Each time DPS is run, test results are written to the hard drive. Your service...
Hardware Reference Guide - Page 5
... Bezel ...15 Using the HP MP 8000r in a Tower Orientation 16 Installing Additional Memory 17 DIMMs ...17 DDR3-SDRAM DIMMs 17 Populating DIMM Sockets 18 Installing DIMMs ...19 Removing or Installing an Expansion Card 22 Drive Positions ...28 Installing and Removing Drives 29 System Board Drive Connections 30 Removing an External 5.25-inch Drive 31 Installing an Optical Drive into the 5.25...
HP SignagePlayer Imaging Tool - Page 1
... OS image for the specific model of HP SignagePlayer.
System Requirements
Software
• Microsoft® Windows® 7 • Microsoft® Windows® Vista or Microsoft® Windows® XP
Hardware
• A desktop PC and one or more HP SignagePlayers • 4GB USB flash device (if using the USB Format option)
Compatible USB flash devices are available from http://www.hpshopping...
HP SignagePlayer Imaging Tool - Page 2
.... Not all USB flash devices have been tested with the HP SignagePlayer Imaging Tool.
Before using the utility, you must download the appropriate image from http://www.hp.com/#Support.
Getting Started
Three deployment options are supported by this utility. You can choose to do one or both of the following: • Create a bootable flash image on a USB flash device (such as a drive key...
HP SignagePlayer Imaging Tool - Page 3
... image is copied to it. To prevent loss of data, be sure that you have saved any user-created data from the flash drive. During the first restart of the SignagePlayer following the restore process, there may be a delay of approximately 510 minutes to unbundle the software before the Windows Desktop is displayed.
Formatting a USB Flash Device
1. Connect your USB flash device (drive key). Ensure...