TP-Link TL-PA4010KIT driver and firmware
Drivers and firmware downloads for this TP-Link item
Related TP-Link TL-PA4010KIT Manual Pages
Download the free PDF manual for TP-Link TL-PA4010KIT and other TP-Link manuals at ManualOwl.com
TL-PA4010 V1.0 User Guide - Page 3
... with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to...
TL-PA4010 V1.0 User Guide - Page 6
... Instruction 6 2.5 Hardware Connection - Computer 6 2.6 Hardware Connection - Internet 7 Chapter 3 Installing Management Utility 9 Chapter 4 Using the Management Utility 13 4.1 Status 13
4.1.1 Set Local Device's Network Name 14 4.2 Network 15
4.2.1 Rename the Remote Device/Enter Password 16 4.2.2 Add Device 16 4.3 Advanced 17 4.4 System 18 4.4.1 Upgrade Firmware 19 4.4.2 Reset Device...
TL-PA4010 V1.0 User Guide - Page 8
... two AC 100V~ 240V power outlets with standard home power wiring b) A computer with the following:
Operating System with TCP/IP installed Pentium III compatible processor and above Ethernet LAN card installed with TCP/IP protocol 64 MB RAM or more 50 MB of free disk space (Minimum) CD-ROM Drive
1.3 Important Safety Instructions
1. Do not open...
TL-PA4010 V1.0 User Guide - Page 15
...before installing this provided software.
Note:
To install Management Utility, please make sure that WinPcap 4.1.2 has been installed in your computer. Otherwise, a window will pop up for you to install WinPcap 4.1.2. Take the following procedures to properly install the provided Management Utility: Step 1: Insert the Resource CD into your CD-ROM drive, and then the following Setup Wizard...
TL-PA4010 V1.0 User Guide - Page 18
TL-PA4010 AV500 Nano Powerline Adapter
Step 3: After the installation, a shortcut to the "Powerline Utility" application icon is provided on the windows desktop.
12
TL-PA4010 V1.0 User Guide - Page 19
... installed the Powerline Adapter hardware and Management Utility software, you can set up or configure the devices according to your need. This Powerline Utility enables the users to identify powerline devices on the powerline network, measures data rate performance and ensures privacy by setting user defined secure powerline networks.
Double click on the icon "
" from your windows desktop...
TL-PA4010 V1.0 User Guide - Page 20
...own password by default, which can be also found on the back of the adapter. Firmware: Displays the current firmware version used by the adapter. Refresh: Click the Refresh button to update the information. 4.1.1 Set Local Device's Network Name To set the local device's network name, please take the following steps: (1) Click Status tab to display the Status tab window. (2) Enter...
TL-PA4010 V1.0 User Guide - Page 21
... the name of the remote device found in the network. You can change its name
following two steps: select the desired adapter and click the Modify button. MAC Address: Displays the MAC address of the remote device found in the network. Password: Displays the supplied Powerline Adapter's password (Initially left blank). To set the
Powerline Adapter password (Which is required when...
TL-PA4010 V1.0 User Guide - Page 23
TL-PA4010 AV500 Nano Powerline Adapter
4.3 Advanced
The third tab window labeled "Advanced" is for Quality of Service. With the proper configuration, the limit bandwidth can...provide higher QoS for streaming data, priority levels can be set using tags at the beginning of data frames. Virtual Local Area Network (Vlan) 802.1p priority tags on Ethernet frames are used to specify 8 (0~7) levels of "user...
TL-PA4010 V1.0 User Guide - Page 24
... highest priority while CAP 0 is the lowest priority. The values shown in VLAN Tags Priority are the default settings for the first running.
4.4 System
The System tab window is for some basic settings of the adapter. On this tab window, you can upgrade the firmware to the latest version, reset the adapter's settings to the factory defaults and configure all...
TL-PA4010 V1.0 User Guide - Page 25
TL-PA4010 AV500 Nano Powerline Adapter
4.4.1 Upgrade Firmware Click the Upgrade Firmware button to upgrade the version of the firmware for the adapter and the following dialog will pop up.
NVM: None-volatile memory. It is used for upgrading the firmware. PIB: Parameter Information Block. It contains configuration values that establish device
network identity, general capabilities...
TL-PA4010 V1.0 User Guide - Page 26
... Adapter
If you want to upgrade the version of firmware for the device, please select appropriate Firmware and PIB files together. New firmware versions and PIB files are posted at www.tp-link.com and can be downloaded for free.
Note:
The parameter information of PIB will restore to the factory defaults after resetting the PLC. To upgrade the device's firmware, follow these instructions...
TL-PA4010 V1.0 User Guide - Page 29
... technical support.
2. The
Ethernet LED does not light up.
Ans. Check the following:
1. Make sure that the Ethernet cable (RJ-45) is properly connected to the Powerline Adapter's Ethernet port.
2. Make sure that the other end of the Ethernet cable (RJ-45) is properly connected to the computer LAN card or to you Cable/xDSL Ethernet port.
3. Make sure your computer LAN card is properly installed...
TL-PA4010 V1 Quick Install Guide EU - Page 1
Quick Installation Guide
AV500 Nano Powerline Adapter
Applicable to TL-PA4010, TL-PA411, and their multiple-pack kits
* This QIG uses TL-PA4010KIT(EU) as an example.
7106505257 REV2.0.0
Plug and Play
Powerline
Router
Adapter
2
LAN
1
WAN
Adapter
Wait until the Powerline LED turns on.
3
More: To add additional Powerline devices with the default settings, simply plug them into the wall ...
TL-PA4010 V1 Quick Install Guide EU - Page 2
... network.
http://www.tp-link.com/en/support/faq Scan the QR code to access the Technical Support page.
More advanced con gurations, such as reset, rmware upgrade and QoS con guration, can be accessed through the Powerline Utility. You can install the Powerline Utility from the resource CD (for Windows only) or download it from the TP-LINK o cial website (for Windows...