TRENDnet TFM-560R driver and firmware
Related TRENDnet TFM-560R Manual Pages
Download the free PDF manual for TRENDnet TFM-560R and other TRENDnet manuals at ManualOwl.com
Data Sheet - Page 1
...all major Network Operating Systems High speed 56Kbps data and 14.4Kbps fax communication Industry standard protocol for data compression and error correction 5 Year Warranty
BENEFITS
User Friendly: Just plug the card into your workstation and it's ready to go!
Flexibility: A single card supports both V.90 and K56Flex data/fax modem.
Compatability: The TFM-560R card supports a variety of software...
Data Sheet - Page 2
... back test, Re-mote Digital loop back test
Power Consumption: • Operation: 250mA, Sleep Mode: 17mA
Dialing: • DTMF tone and rotary pulse
Certifications: • FCC, CE 0560 X
NETWORKING SOLUTIONS
PRODUCT INFORMATION
TFM-560R 56Kbps (V.90) High Speed PCMCIA Fax Modem with XpressPort (Lucent Chipset)
TEM100-56R 10/100Mbps Fast Ethernet + 56Kbps Fax Modem Card with XpressPort
To Order...
Manual - Page 1
... Board Services (BBS) or computer networks such as Compuserve.
Unpacking Information
The PC Card fax/modem package includes following contents: • User's Manual • One Type II Fax/Modem PC Card. • One detachable interface connector with RJ-11 cable and
plug. • FAX & Data Communication software package. • One RJ-11 plug to phone jack converter. • One INF file disk...
Manual - Page 2
... use the AT commands to control the fax/modem manually.
What You Need to Use Your Modem
Following components are essential to run the Fax/Modem PC Card:
1. A computer with PCMCIA type II slot. 2. PCMCIA Socket Service and Card Service drivers. (These
drivers are usually included with the computer. If not, ask your computer dealer for details.) 3. The Fax/Modem PC Card. 4. A telephone line with RJ...
Manual - Page 3
...
1. Turn on your computer. 2. Insert the Fax/Modem PC Card into the free PCMCIA slot, and
make sure it is firmly seated. 3. Windows 98 will prompt New Hardware Found then Add
New Hardware Wizard dialog box. Click Next. 4. Select "Search for the best driver for your device
(Recommended)", and click Next.
5. Insert Fax/Modem PC Card driver disk, select "Floppy disk drives", and click...
Manual - Page 4
... computer. 2. Insert the Fax/Modem PC Card into the free PCMCIA slot,
and make sure it is firmly seated. 3. Windows 95 will prompt New Hardware Found dialog box.
Select Driver from disk provided by hardware manufacturer, and click OK. 4. Enter the path A:\, and insert Fax/Modem PC Card INF file disk. Windows 95 will install the modem driver autmatically. 5. Connect the FAX/MODEM interface cable...
Manual - Page 5
Working with Windows 3.1 & Workgroups
Before installation, make sure the PCMCIA Card Service and Socket Service drivers has been installed in your computer already, most of the notebook computers have those drivers by default. If not, ask your computer dealer to have one.
1. Turn on your computer. 2. Insert the Fax/Modem PC Card into the free PCMCIA slot,
and make sure it is firmly seated. 3. You ...
Manual - Page 6
☛ Note: Insert FAX/MODEM before running communication program.
Working with DOS
Before installation, make sure the PCMCIA Card Service and Socket Service drivers has been installed in your computer already, most of the notebook computers have those drivers by default. If not, ask your computer dealer to have one. 1. Turn on computer. 2. Insert the Fax/Modem PC Card into the free PCMCIA slot,...
Manual - Page 8
... Card Services, you can use the enabler in the bundled INF file disk to enable the Fax/Modem.
The enabler can be installed as DOS command or DOS driver. It means that you can load the enabler from the DOS prompt or put it in the AUTOEXEC.BAT or CONFIG.SYS to load the driver every time you start your computer...
Manual - Page 9
...NT
1. Plug the Fax/Modem PC Card into the PCMCIA slot. 2. Run Windows NT 4.0. 3. Double click the Modem Icon in Control Panel. 4. In Install New Modem window, press Next button to detect
the modem automatically. 5. Press Change button to change the modem type. 6. Press Have Disk... button. 7. Insert the INF file disk bundled with the fax/modem PC Card
to the floppy drive. 8. Enter the path A:\ and...
Manual - Page 10
... All commands and command-values accepted by the modem, the OK message will be shown; any entries other than those show OK response cause the ERROR result code.
This chapter describes how to use...your software to loose its ability to control the modem. When you do find any AT command causes fax/modem maul-function, turn the computer off and then on. That will reset most of the AT command settings to...
Manual - Page 13
... port for the Fax/Modem PC Card to another unused port. It might be better to set the COM port to COM3: or COM4:. Refer to Appendix B for choosing a new COM port. Even if you are not using the serial port which is set to the same COM port as the modem, it can still interfere with the modem. Be sure to update your software COM port setting...
Manual - Page 14
... on the third ring.
P: The software does not control the modem properly or can not detect the modem.
S: Make sure the software has been set up correctly. Check the initialization and dial strings.
C: Some TSRs (programs that stay in memory after they are loaded) may conflict with the communications software.
S: Try starting your computer without loading any TSRs.
P: The characters on...
Manual - Page 15
... phone line that requires rotary pulses dialing, it may not work. Try ATDP###### instead of ATDT#######.
P: When your communications software drives the modem to make dialing, the PC Card does not take any action.
C: Make sure the ATDT dialing prefix is correctly set in the software you are using.
C: Make sure the software and modem are set to consistent COM port...
Manual - Page 16
... not make any sound when you're connecting to another modem.
C: The software may have the speaker disabled. S: Change the setting in your software or use the ATMn
command to turn the speaker on
P: The modem disconnects (looses the connection) in the middle of use.
C: The remote modem may have locked up. C: The telephone line may have...
Manual - Page 17
... V.42 protocol, then the flow control may not be setup correctly.
S: Configure your software to use RTS/CTS flow control. That will cause your computer to pause long enough for the file to be stored to disk.
P: The text on the screen is not legible.
C: Your software settings may not match the settings on the remote modem's software.
S: Make sure your data...
Manual - Page 18
...: V.42bis and MNP 5 Communication software compatible commands:
Hayes compatible enhanced "AT" command set Fax Service Class 1 commands Built-in DTE interface: DTE speed up to 115,200 bps 16C550 UART interface NVRAM directory stored profiles Flow control (XON/XOFF, RTS/CTS) Speed buffering Automatic format/speed sensing Diagnostics: Remote digital loop and remote digital loop self test Analog loop...
Manual - Page 22
... 10 pps, Japanese version (Default)
Async communications mode options
Async mode, buffered (same as "AT\N0")
Error control mode, buffered (same as "AT\N3")
MNP error control mode. If an MNP error control protocol is not established, the modem will fallback according to the current setting in S36 register.
V.42 or MNP error control mode. If neither error control protocol is established, the...
Manual - Page 23
...
Local digital loopback (LDL) test
&T6
Remote digital loopback test, in normal
mode
View active file and stored phone numbers
Store active configuration into the modem's NVRAM
Store telephone number
n=0 to 3
x= see also the dial modifier in "ATDn" command
The max. number of digits per string is 40.
Manufacturer default
Extended "AT\" (Back Slash) Command Set
Command...