Netgear GS516TP driver and firmware
Related Netgear GS516TP Manual Pages
Download the free PDF manual for Netgear GS516TP and other Netgear manuals at ManualOwl.com
Hardware Installation Guide - Page 22
... of its overall performance as well as the performance of the network. After powering up the switch for the first time, the smart switch can be configured using a web browser or a program called Smart Control Center. For more information about managing the switch, see the software administration manual on the smart switch resource CD.
Installation 22
Hardware Installation Guide - Page 25
... the switch and the connecting device. Ensure that all cables used are correct and comply with Ethernet specifications. Check for a defective computer adapter card, cable, or port by testing them in an alternate environment where all products are functioning.
File transfer is slow or performance degradation is a problem.
Half-duplex or full-duplex setting on the switch and the...
Hardware Installation Guide - Page 28
... devices and sets system
configuration to each switch. • Configuration backup and restore (easy to configure more than one switch) • Password access control • Firmware upgradeable
Interface
• Sixteen 10/100/1000 Mbps AutoSensing Gigabit Ethernet switching ports • Ports 1-8 are PoE PSE ports providing up to 15.4W power • Ports 15-16 are PD ports receiving power...
Hardware Installation Guide - Page 30
... limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Declaration Of Conformity We, NETGEAR, Inc., 350 East Plumeria Drive...
Installation Guide - Page 1
... icon in the Windows Start menu to run the utility and view this screen.
Internet
2. Connect the switch to your network.
3. Power on the switch by connecting the AC power cord to an outlet, or by connecting an Ethernet cable from PD ports 15 or 16 (or both) to a PSE device.
4. Verify that the computer with the Smart Control Center Utility...
Installation Guide - Page 2
...settings of the computer are correct. In most cases, computers should be configured to obtain an IP address through DHCP. If your network uses static IP addresses, be sure that the switch and computer are configured with valid IP addresses. For more information, see the software administration manual.
Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial...
Software Administration Manual - Page 11
... using the web-based management interface. NETGEAR provides the Smart Control Center utility with this product. This program runs under Windows XP, Windows 2003, Windows 2008 or Windows 7 (32 bit and 64 bit) and provides a front end that discovers the switches on your network segment (L2 broadcast domain). When you power up your switch for the first time...
Software Administration Manual - Page 17
...
Configure the Network Settings on the Administrative System
If you do not use the Smart Control Center to configure the switch network information, you can connect directly to the switch from the administrative system installed on your computer. The IP address of the administrative system must be in the same subnet as the default IP address on the...
Software Administration Manual - Page 53
... location, 911, Layer 2 switch support, and device information management capabilities.
Hardware Revision
The hardware version advertised by the remote device.
Firmware Revision
The firmware version advertised by the remote device.
Software Revision
The software version advertised by the remote device.
Serial Number
The serial number advertised by the remote device.
Model Name
The model...
Software Administration Manual - Page 73
...port or port channel.
• Fast Link. Specifies if the specified port is an edge port with the CST. Possible values are Auto, Enable, or Disable. The default is Auto, which specifies that the software...31, the priority is set to 16.
• Port ID. The port identifier for the specified port within the CST. It is made up from the port priority and the interface number of the port.
• Hello ...
Software Administration Manual - Page 88
... contains up to 32 multicast service groups. To add a multicast group: 1. Select Switching > Multicast > Static Multicast Address > Multicast Group
Configuration. 2. Select the VLAN ID.
• VLAN ID. Displays the VLAN ID. • VLAN Name. Displays the user-defined VLAN name. 3. In the Multicast Address field, enter the multicast group MAC Address associated with the VLAN. •...
Software Administration Manual - Page 99
... associates a Layer 2 MAC address with a Layer 3 IPv4 address. The software features both dynamic and manual ARP configuration. With manual ARP configuration, you can statically add entries to the ARP table. ARP is a necessary part of the Internet Protocol (IP) and is used to translate an IP address to a media (MAC) address, defined by a local area network (LAN) such as Ethernet. A station needing...
Software Administration Manual - Page 124
... is automatically logged out and must reenter the password to access the management interface. A value of zero corresponds to an infinite timeout. The default value is 5 minutes. The Maximum Number of HTTP Sessions is 5. 3. Click APPLY to update the switch with the HTTPS Authentication settings.
Secure HTTP Configuration
Secure HTTP enables the transmission...
Software Administration Manual - Page 135
...network resources. ACLs are used to provide traffic flow control, restrict contents of routing updates, decide which types of traffic are forwarded or blocked, and above all provide security for the network. The switch software supports IPv4 and MAC...MAC addresses, and other packet-matching criteria. Finally, use the ID number to assign the ACL to a port...ACL, see the instructions on the ACL ...
Software Administration Manual - Page 164
... software image, which is saved in one of two flash sectors called images (image1 and image2). The active image stores the active copy and the other image stores a second copy. The device ... is to download a working configuration from a device, edit it offline to personalize it for another similar device (for example, change the device name, IP address), and upload it to that device. •...
Software Administration Manual - Page 166
... it offline to personalize it for another similar device (for example, change the device name, IP address), and download it to that device. • Boot. File that contains code that runs when the switch is brought up. It performs initiation actions and loads the software.
The Download menu contains links that provide access to the features described in...
Software Administration Manual - Page 167
GS516TP Gigabit Smart Switches
Note: The system always downloads the software image to the non-active image.
• Text Configuration. A text-based configuration file. • Boot. Code that runs when the switch is brought up. It performs initiation actions and
loads the software. 3. From the Server Address Type field, select the format for the address you type in...
Software Administration Manual - Page 168
GS516TP Gigabit Smart Switches
3. In the Select File field, enter the name of the file that you want to download or click Browse to open a file upload window to locate the file.
4. Click the APPLY button to initiate the file download. Note: After a file transfer is started, wait until the screen refreshes. When the screen...
Software Administration Manual - Page 169
GS516TP Gigabit Smart Switches
File Management
The system maintains two versions of the switch software in permanent storage. One image is the active image, and the second image is the backup image. The active image is loaded during subsequent switch restarts. This feature reduces switch down time when upgrading or downgrading the switch software. The File Management menu...
Software Administration Manual - Page 180
GS516TP Gigabit Smart Switches
Feature Password control access
Management security
Port MAC lock down Boot code update DHCP/manual IP Default gateway System name configuration Configuration save/restore Firmware upgrade Factory default reset Dual image support Factory reset Multi-session web connections SNMPv1/V2c SNMP v3 Time control LLDP/LLDP-MED Logging MIB Support Smart Control Center ...