TP-Link T2500G-10MPS driver and firmware
Drivers and firmware downloads for this TP-Link item
Related TP-Link T2500G-10MPS Manual Pages
Download the free PDF manual for TP-Link T2500G-10MPS and other TP-Link manuals at ManualOwl.com
T2500G-10MPSUN V1 Configuration Guide - Page 6
...Device Description...29 Setting the System Time...30 Setting the Daylight Saving Time...32 Specifying the Serial Port...51 Upgrading the firmware...51 Configuring Auto Install ...Function...52 Rebooting the switch...53 Configuring the Reboot Schedule...54 Reseting the Switch...55 Access Security Configurations...56 Using the GUI...56 Configuring the Access Control...
T2500G-10MPSUN V1 Configuration Guide - Page 29
... egress-rate is used to restrict ingress and egress bandwidth.
More Information
The latest software and documentations can be found at Download Center at http://www.tp-link.com/support.
The Installation Guide (IG) can be found where you find this guide or inside the package of the switch.
Specifications can be found on the...
T2500G-10MPSUN V1 Configuration Guide - Page 47
... Schedule function is used to set a schedule for the switch to reboot.
Access Security Access Security provides different security measures for accessing the switch remotely so as to enhance the configuration management security. Access Control function is used to control the users' access to the switch by filtering IP address, MAC address or port. HTTP Config function is...
T2500G-10MPSUN V1 Configuration Guide - Page 56
..., Hardware Version, Firmware Version, System Time, Run Time and so on.
end Return to privileged EXEC mode.
copy running-config startup-config Save the settings in the configuration file.
The following example shows how to set the device name as Switch_A, set the location as BEIJING and set the contact information as http://www.tp-link.com.
Switch#configure
Configuration Guide 29
T2500G-10MPSUN V1 Configuration Guide - Page 71
...the switch Back up the configuration file Upgrade the firmware Configure the Auto Install Function Reboot the switch Configure the ...load the following page.
Figure 4-1 Configuring the Boot File
Follow these steps to configure the boot file: 1) In the Boot Table section, select one or more units and configure the relevant
parameters.
Configuration Guide...
T2500G-10MPSUN V1 Configuration Guide - Page 73
... > Firmware Upgrade to load the following page.
Figure 4-4 Upgrading the Firmware
In the Firmware Upgrade section, select one file and click Upgrade to upgrade the system.
Firmware File
Select the desired firmware file to upgrade the system.
Image Name
Displays the image to upgrade. It means that the operation will only effect the backup image.
Firmware Version
Displays the current firmware...
T2500G-10MPSUN V1 Configuration Guide - Page 74
... Configurations
After upgrading, the device will reboot automatically with the backup image
Select this option to reboot automatically with the backup image after upgrading.
4.1.5 Configuring Auto Install Function
Note:
You should configure the DHCP server and the TFTP server first before configuring the Auto Install function.
Choose the menu System > System Tools > Auto Install to load the...
T2500G-10MPSUN V1 Configuration Guide - Page 78
... backup the configuration file named file2 from TFTP server with IP address 192.168.0.100. Switch>enable Switch#copy startup-config tftp ip-address 192.168.0.100 filename file2 Start to backup user config file...... Backup user config file OK.
4.2.4 Upgrading the firmware
Follow these steps to upgrade the firmware:
Step 1
enable Enter privileged mode.
Configuration Guide 51
T2500G-10MPSUN V1 Configuration Guide - Page 79
...#firmware upgrade ip-address 192.168.0.100 filename file3.bin It will only upgrade the backup image. Continue? (Y/N):Y Operation OK! Reboot with the backup image? (Y/N): Y
4.2.5 Configuring Auto Install Function...downloaded as startup configuration file automatically.
Step 4
boot autoinstall auto-reboot
Enable the auto reboot mode and the switch will reboot automatically after the auto install ...
T2500G-10MPSUN V1 Configuration Guide - Page 80
... 8
boot autoinstall start Start the Auto Install process and the switch will download the configuration file and the backup image automatically.
end Return to privileged EXEC mode.
copy running-config startup-config Save the settings in the configuration file.
Note:
• The switch will obtain a new IP address from the DHCP server during the process...
T2500G-10MPSUN V1 Configuration Guide - Page 87
... authentication, encryption and message integrity to allow secure HTTP connection.
TLS Version 1
Select Enable to make the switch support TLS Version 1 protocol.
TLS is a transport protocol upgraded from SSL. It supports a different encryption algorithm from SSL, so TLS and SSL are not compatible. TLS can support a more secure connection.
2) In the CipherSuite Config section, select the...
T2500G-10MPSUN V1 Configuration Guide - Page 298
.... It also receives the other user packets to update its MAC address table, but doesn't forward them.
Forwarding In this status, the port receives and sends BPDUs. It also receives the other user packets to update its MAC address table, and forwards them.
Disabled In this status, the port is not participating in the spanning tree...
T2500G-10MPSUN V1 Configuration Guide - Page 299
... packets to update its MAC address table, and forwards them.
Disconnected
In this status, the port is enabled with spanning tree function but not connected to any device.
Path Cost The path cost reflects the link speed of the port. The smaller the value, the higher link speed the port has.
The path cost can be manually configured on...
T2500G-10MPSUN V1 Configuration Guide - Page 596
... Security
Client
A client, usually a computer, is connected to the authenticator via a physical port. We recommend that you install TP-Link 802.1X authentication client software on the client hosts, enabling them to request 802.1X authentication to access the LAN.
Authenticator
An authenticator is usually a network device that supports 802.1X protocol. As the above figure shows...
T2500G-10MPSUN V1 Configuration Guide - Page 694
...to advertise the detailed PoE information including power supply priority and supply status between LLDP-MED Endpoint devices and Network Connectivity devices.
Used to advertise the inventory information. The Inventory TLV set contains seven basic Inventory management TLVs, that is, Hardware Revision TLV, Firmware Revision TLV, Software Revision TLV, Serial Number TLV, Manufacturer Name TLV, Model...
T2500G-10MPSUN V1 CLI Reference Guide Guide - Page 9
....29 21.30 21.31 21.32 21.33 21.34 21.35
system-time manual ...161 system-time ntp ...161 system-time dst predefined 163 system-time dst date...address ...168 ip address-alloc...169 reset ...170 reboot ...170 reboot-schedule ...171 copy running-config startup-config 172 copy startup-config tftp ...172 copy tftp startup-config ...173 boot application ...174 remove backup-image...174 firmware upgrade...
T2500G-10MPSUN V1 CLI Reference Guide Guide - Page 22
... USB port on the MAC OS X or Linux OS for console connection, there is no need to run a USB driver. If you are using the switch's Micro-USB console port with the USB port of a Windows PC, a driver for the USB port is required. The USB driver is provided on the resource CD. Follow the InstallSheild Wizard to accomplish the installation. The TP-Link USB Console Driver supports the following Windows...
T2500G-10MPSUN V1 CLI Reference Guide Guide - Page 23
64-bit Windows 8 32-bit Windows 8.1 64-bit Windows 8.1 After the TP-Link USB Console Driver is installed, the PC's USB port will act as RS-232 serial port when the PC's USB port is connected to the switch's Micro-USB console port. And the PC's USB port will act as standard USB port when the PC's USB port is unplugged from the switch. Logon Take the following ...
T2500G-10MPSUN V1 CLI Reference Guide Guide - Page 194
T2500G-10MPS# firmware upgrade ip-address fe80::1234 filename firmware.bin It will only upgrade the backup image. Continue? (Y/N):y
Operation OK! Reboot with the backup image? (Y/N): n
21.20 boot autoinstall start
Description
The boot autoinstall start command is used to start Auto Install function. To stop the Auto Install function, use no boot autoinstall start.
Syntax
boot autoinstall start no...
T2500G-10MPSUN V1 Installation Guide - Page 24
... on devices connected to both console ports, but console input is only active on one console port at a time. The Micro-USB connector takes precedence over the RJ-45 connector. Install the TP-Link USB Console Driver if you are using the USB serial port for the first time on a Windows-based PC. The driver can be found on the attached CD and Download page...