Brother International LS-2125i - Basic Sewing And Mending Machine driver and firmware
Drivers and firmware downloads for this Brother International item
Related Brother International LS-2125i Manual Pages
Download the free PDF manual for Brother International LS-2125i and other Brother International manuals at ManualOwl.com
Users Manual - Multi - Page 54
...No
Upper thread is tangled.
Page 16
No
Upper thread tension is too
tight.
Page 20
No
Spool of thread is not correctly
installed.
Page 12
No
Needle is bent or not sharp.
Lower (bobbin) thread is tangled.
Page 17
No
Bobbin is not threaded
properly...Page 6
No
The combination of needle size/
thread size/fabric is incorrect.
Page 22
No
Page 16
No
CONTACT YOUR LOCAL SERVICE CENTER
46
Users Manual - Multi - Page 55
...MACHINE IS NOISY OR
SLOW
MACHINE DOES NOT
START
The combination of needle size/
thread size/fabric is incorrect.
Page 22
No
Damaged or worn needle is used.
Page 6
No
Thread is tangled.
Pages 12-17 No
Darning plate is installed... pull the fabric.
No
Power supply plug is removed
from outlet.
Page 4
No
Main power switch is turned
off.
Page 5
No
Foot controller is not used correctly.
...
Users Manual - English - Page 5
... to assure correct installation. For repair or adjustment In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer. For additional product information and updates, visit our...
Users Manual - English - Page 10
... plate The needle plate is marked with guides for sewing straight seams.
f Shuttle hook
g Shuttle cover Open the shuttle cover to set the bobbin.
h Bobbin case
i Needle
j Needle bar thread guide
k Needle clamp screw Use the needle clamp screw to hold the needle in place.
a Flat bed attachment b Storage compartment
Note
● Put the accessories...
Users Manual - English - Page 11
.... We have designed these accessories to help you
be able to carry out most sewing tasks.
1
Note
(For U.S.A. only)
● Foot controller: Model KD-1902, N This foot controller can be used on the following machine models: LS-2220/2720/1520/2125/2125i.
● The screw of the presser foot holder is available through your authorized dealer...
Users Manual - English - Page 13
...the machine, set the main power c switch to "{".
X The sewing lamp goes off when the machine is turned off.
Foot controller CAUTION
Note
● If a power outage occurs while the sewing machine is being operated, turn off the
● When connecting the foot controller, be sure
1
to turn off the sewing machine in order to
prevent the machine from accidentally being
started.
sewing machine...
Users Manual - English - Page 16
...SEWING MACHINE
Lower threading
Install the bobbin wound with thread.
Open the shuttle cover behind the flat bed b attachment at the front of the machine... turn the power off while threading the machine. If you accidentally step on the foot controller and the machine starts to sew, you could... designed to be used with this machine.
CAUTION
● Make sure you set the bobbin so the thread unrolls...
Users Manual - English - Page 17
... the shuttle race.
a Bobbin case finger b Notch
Close the shuttle cover.
g
CAUTION
● Make sure that the bobbin case is properly placed back into the machine. If it is incorrectly installed, it will fall out from the shuttle when the machine starts to sew.
1
15
Users Manual - English - Page 21
...instructions below.
CAUTION
● Only use home sewing machine needles. Use of any other needle may bend the needle or damage the machine... types
The sewing machine needle that ...sew. Use the same size thread for the upper (spool) and lower (bobbin) threads.
Sewing..., Muslin
90/14 (Supplied with your machine.)
Cotton: 50-60 Silk: "A" Synthetic... ball point needle when sewing on stretch fabrics or ...
Users Manual - English - Page 23
...much, the needle clamp (which holds the needle) may fall off.
Install the twin needle in the same way.
Therefore, do not loosen the... or tightening the needle clamp screw, otherwise certain parts of the sewing machine may be damaged.
CAUTION
● Be sure to insert the ...needle bar thread guide is at the bottom.
With the flat side of the needle toward the e rear of the machine, insert the needle...
Users Manual - English - Page 26
...of the presser bar.
Removing the presser foot holder
Remove the presser foot holder when cleaning the sewing machine or when installing a presser foot that does not use the presser foot holder, such as the quilting foot....
Note
● If the presser foot holder is not correctly installed, the thread tension will be incorrect.
a Screwdriver b Presser foot holder c Presser foot holder screw
24
Users Manual - English - Page 49
... any accumulated lint g and thread from the retaining ring, hook,
driver and race body.
CAUTION
● Make sure you unplug the machine before you clean it. Otherwise, you may get an electric shock or...by using a coin or d screwdriver to remove the screws.
a Retaining ring b Driver c Race body
Use a cloth dampened with machine oil to h wipe the shuttle race in order to remove any
lint.
Clean the...
Users Manual - English - Page 53
... plate. Contact your retailer or the nearest authorised service center.
-
The upper thread breaks.
The area...machine.
Incorrect bobbins will not work properly. Only use a bobbin that has been designed for this machine.
page 12
Bobbin is set incorrectly.
Reset the bobbin thread correctly.
page 14
The upper thread is too tight.
The bobbin thread is incorrectly installed.
Correctly install...