Brother International BES-1241BC driver and firmware
Drivers and firmware downloads for this Brother International item
Related Brother International BES-1241BC Manual Pages
Download the free PDF manual for Brother International BES-1241BC and other Brother International manuals at ManualOwl.com
Thread Tensions - English - Page 1
... tension problems as found on Brother embroidery equipment. They are listed in the order that they most often occur. Use this form only as a guide. Following this guideline will help...a Brother Anti-Spin Spring p/n#S35583001, which comes in the Brother bobbin case assembly p/n#S35584001. !" When do you check it? At installation of machine and at every bobbin change. !" How do you check it? Install a...
Thread Tensions - English - Page 2
...constant, works with top thread to form a proper stitch. !" When do you check it?
At install and at every bobbin change. When tensions are believed to be the problem,
ALWAYS check and adjust ...tension
gauge. The guage will take into account the
pressure of the anti-spin spring while setting
the tension. Adjust the bobbin tension after
adjusting the anti-spin spring and cleaning
under the ...
Thread Tensions - English - Page 3
...-4BROTHER
3. Main Tensioners
!" What are they for? Main upper thread tension control of machine. !" When do you adjust them? At install, then only after bobbin has been cleaned and adjusted first. Run a tension test first, if you are still having trouble check the thread path and rethread the complete path for the troublesome...
Knife Adjustments - English - Page 3
... machine and re-check the adjustment. You may have to do this more than once to achieve the correct position.
Moving Knife Adjustment Screws
Re-install the arm cover and the needle plate and your finished. If you find that the machine will still not cut the thread cleanly, you might...
Motor Locks - English - Page 1
... for the main motor to turn the degree wheel or pulley causing a motor lock error. Listed below are some causes of the problem. Listed in the order that they occur... application • Needle being installed backwards • Worn needles • Incorrect backing for the application. • Loose upper thread tension • Inner rotary hook adjuster set incorrectly
Rotary Hook
Foreign object...
Upper Thread Breaks - English - Page 1
... thread is not threaded correctly o Correctly thread the machine
• Upper thread tension is to tight o Reduce upper thread tension
• Needle is not installed correctly o Install needle correctly
• Needle is bent or worn o Replace the needle
• Presser foot height is incorrect o Adjust presser foot height to thickness of material...
Optional Functions Instruction Manual - English - Page 9
... only when the device to read from is set to
floppy disk,
personal
computer or memory.
network. Automatic input is not available if the device to read from is set to
■ To choose
network as the device and to read the data via the network will require another software
and so on. Please consult our sales office or service station nearby in...
Maintenance Schedule - English - Page 3
...Call Toll Fre e 1-877-4BROTHER Email: tsupport@brother.com
Website: http://www.brother-usa.com/industembroidery/tech_down.aspx
Monthly Maintenance
Cleaning
Knives
Control Box
1. Remove the two rear screws and remove... and back of control box.
2. Clean any thread and lint around the moving and fixed knives with a brush or compressed air. Do this for all heads.
3. Re-install needle plates. 5/24...
Tubular to Cap - English - Page 1
... or stop position.
8) Switch the machine to cap mode.
Computer model - On the computer left click on Settings, Embroidery
Hoop, Wide Cap (All).
Stand Alone - Use the flat/cap switch on the panel to switch to cap.
9) Turn machine off for 5 seconds and power back on. It will ask you to confirm
canceling the...
Cap to Tubular - English - Page 1
...the driver for safekeeping.
5) Move the needle case to needle #1 using the needle select buttons
.
6) Remove the cap needle plates (A) and replace with the flat needle plates.
7) Manually ...Computer model - On the computer left click on Settings, Embroidery Hoop, Tubular (All).
Stand Alone - Use the flat/cap switch on the panel to switch to flat.
12) Turn machine off for 5 seconds and power...
Instruction Manual - English - Page 4
...power switch and disconnecting the power cord from the wall outlet before opening the face plate of the control...power and disconnect the power cord from the wall outlet. Lightning may cause problems with correct operation.
Installation
Machine installation should only be carried out by a qualified technician.
Contact your Brother...the reach of children.
Avoid setting up the sewing machine near ...
Instruction Manual - English - Page 5
... hook and knife.
If the power switch needs to be left on when carrying out some adjustment, be extremely careful to observe all safety precautions.
Use only the proper replacement parts as specified by Brother.
If any safety devices have been removed, be absolutely sure to re-install them to their original positions and...
Instruction Manual - English - Page 10
...1241BC (12 needles)
Explanation for individual model is provided by identifying the model name. Check the model before using the machine. The display is BES-941BC.
Configuration of this manual
This manual consists of the following chapters:
Chapter 1 Preparation of Embroidery Machine This Chapter describes the specifications, installation... 5 Setting This Chapter describes procedures of setting the ...
Instruction Manual - English - Page 11
Chapter 9 List of Error Messages Provides information on error codes and action to be taken.
Chapter 10 Troubleshooting Provides troubleshooting for the machine.
Connection and Installation of Optional Equipment Describes connections between the machine/computer and optional equipment available.
BES-941BC • BES-1241BC
9
Instruction Manual - English - Page 14
... Preparation for Embroidering 55 Turn on the Machine Power 56 Retrieve the Embroidery Data 57 Start Embroidering 57
Chapter 3 Selection of Data and Embroidering
What Can the Machine Do 60 Selection of Data 61
Registration of Embroidery Data from Floppy Disk 61 Reading from Memory 64 Registration of Embroidery Data from BE-100...
Instruction Manual - English - Page 17
... 2. Oiling 137
2-1 Head ...137 3. Greasing 139
3-1 Head ...139 3-2 Feed Guide Section 143 3-3 Lower shaft module 144
Chapter 8 Standard Adjustment
1. Adjusting Needle Bar ... the Belt Tension 158
Chapter 9 List of Error Message
Chapter 10 Troubleshooting
Mechanical Section 166 Electrical Section 168
Connection and Installation of Optional Equipment
Attaching Bobbin Winder 178
BES-941BC •...
Instruction Manual - English - Page 23
...be laid by your distributor or electric experts.
A machine weighs more than 600 kg. Installation should be carried out by 4 or more workers.
Do not connect the power source until installation is completed. Doing so may start the machine unintentionally through an accidental activation of the ...rear of the machine), and pass them under the legs to lift the machine.
BES-941BC • BES-1241BC
21
Instruction Manual - English - Page 25
3-2 Installation of Machine
r q e w
Chapter 1 Preparation of Embroidery Machine
1. Place the attached cushion sheets w and leveling plates e under the four level adjusters q. The leveling plates e should be ... be rocked during operation. In such a case, it is recommended that a secure base of concrete be placed below the embroidery machine.
BES-941BC • BES-1241BC
23
Instruction Manual - English - Page 49
...Machine
2. For adjusting the height, loosen the screw q and turn the tension spring bracket w. 3. For adjusting the tension spring force, insert a driver tip in the groove of the thread tension
bar e and turn it. Lower thread tension The standard tension of the lower thread is 0.15~ 0.... lower thread will come out smoothly.
0.15~0.3N (15~30gf)
To tighten
To loosen
BES-941BC • BES-1241BC
47
Instruction Manual - English - Page 51
Chapter 2
Embroidering Procedures
After installation of machine start embroidering. This chapter explains about the operation panel on the machine as well as precautions for the actual embroidering process.